User manual ZANUSSI ZI7454.60

[. . . ] Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local Service Centre, and always insist on genuine spare parts. This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. This appliance is designed to be operated by adults. [. . . ] This will prevent it from becoming a death-trap for a child. GB Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brandnew product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special " Building-in" instructions given. Important It is essential that the appliance be connected to an efficient earth tap. For this purpose the supply cable plug incorporates a special earth contact. If the sockets of your domestic wiring system are not earthed, have the appliance connected to a separate earth wire by a qualified electrician in accordance with existing safety regulations. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. . This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent mod)fications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. 39 I nstructions for totally built-in appliances Dimensions of the recess Model ZI 7234 ZI 7194 ZI 7164 2 Height Depth Width 1225 mm 550 mm 560 mm 1030 mm 550 mm 560 mm 880 mm 550 mm 560 mm 50 mm min. 1 The appliance's door has been locked in position for transport by means of pins on both sides. To ensure correct storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. 180° Fig. 10 2 1 PR140 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. TECHNICAL SPECIFICATIONS The technical data is indicated in the rating plate on the left side inside the appliance. GB 42 USE Operation Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, clockwise, beyond the «O» (STOP) position. The appliance will start to operate. GB Temperature regulation The temperature is automatically regulated and can be increased to achieve a higher temperature (warmer) by rotating the thermostat knob toward lower settings or reduced (colder) rotating the knob towards higher settings. However, the exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on: room temperature; how often the door is opened; the quantity of food stored; location of appliance. A medium setting is generally the most suitable. To stop operation, simply turn the thermostat knob to position «O». Important If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption. remember that, in this condition, the refrigerating compartment temperature might drop below 0°C. [. . . ] Under normal circumstances, to freeze fresh foods it is not necessary to change the setting of the thermostat knob with respect to the normal running position. Depress the ambient switch at least 3 hours before loading food to be frozen. However, for a quicker freezing operation, turn the thermostat knob to the coldest setting; but Storage of frozen food To obtain the best performance from this appliance, we strongly recommend that you make sure that the commercially frozen foodstuffs were adequately stored by the retailer and, furthermore, be sure that these frozen foodstuffs are transferred from the foodstore to the consumer in the shortest possible time (a temperature increase of the frozen food could shorten its storage period). 43 It is also advisable not to exceed the storage period indicated by the producer of the food. [. . . ]