User manual ZANUSSI ZL56SA

[. . . ] REFRIGERATOR ZL 56 W ZL 56 SA INSTRUCTION BOOKLET 2222633-71 CONTENTS Instructions for the User Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration The door shelves Normal Operating Sounds Instructions for the Installer 3 4 4 4 4 5 5 5 Technical Specifications Installation Positioning Door reversal 13 13 13 14 Electrical Connection 15 Health and Safety Guidelines Defrosting Maintenance and Cleaning Internal cleaning External cleaning Changing the light bulb When the appliance is not in use 6 6 7 7 7 7 7 Something Not Working?Service and Spare Parts Customer Care Department Service Force Addresses Guarantee Conditions 8 9 9 10 12 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation s General Safety s Check the appliance for transport damage. [. . . ] Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife, without washing them thoroughly in between. s s s s s s s s DEFROSTING The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located at the back of the appliance above the compressor, where it evaporates. Important To avoid defrost water overflowing into the fridge, periodically clean the water discharge hole in the centre of the V shaped drip collector at the back of the refrigerator compartment behind the salad bin. Use the special cleaner provided which you will find already inserted into the discharge hole. D037 6 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Warning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. External cleaning Wash the outer cabinet with warm soapy water. Once or twice a year dust the condenser (black grill) and the compressor at the back of the appliance, with a brush or vacuum cleaner, see the figure. You MUST ensure that the appliance is switched OFF. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. CONDENSER DEFROST TRAY COMPRESSOR D662 Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Service Force Centre). Replace the light cover by sliding it into its original position and replacing the screw. D411 7 SOMETHING NOT WORKING? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom No power to appliance Solution - Check there is power at the socket. - Check there is not a power cut by checking the household lights. - Ensure that the bulb is correctly fitted. - Check the door light switch is not jammed. - Check the ambient temperature is within the appliances operating limits of 10°C to 32°C. Lincs DN32 9AS Unit 1 Boulevard Industrial Estate Hull HU3 4AY 64-66 Cross Gates Road Cross Gates Leeds LS15 7YS KELSO JERSEY GRIMSBY ORKNEY HULL SCOTLAND ABERDEEN 54 Claremont Street Aberdeen AB10 6RA 33a Burnside Auchtermuchty Fife KY14 7AJ Unit 5 Block 2 Auchenraith Ind. Estate Rosendale Way Blantyre G72 0NJ 93 Irish Street Dumfries DG1 2 PQ 7 Hill Street Dunoon Argyll PA23 7AL Unit 12 Dumbryden Ind. Estate 2 Dumbryden Road Edinburgh EH14 2AB Unit 4 Wellington Road Bishopriggs Glasgow G64 2SA Unit 3BI Smithton Ind. [. . . ] When positioning the bottom hinge blade on the reverse side, the securing screws will require a degree of force when fitting. It is therefore advisable to lubricate the screw tips before starting this operation. Important After completion of the door reversal operation, verify that the door gasket is sealing onto the cabinet. If the ambient temperature is cold (i. e. [. . . ]