User manual ZANUSSI ZP3414

[. . . ] Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings or these warnings contact the Customer Care Department. Prior to installation Check the appliance for transport damage. Under no circumstances should a damaged appliance be installed. [. . . ] When the compressor is on, the refrigerant is being pumped round and you will hear a whirring sound or pulsating noise from the compressor. A thermostat controls the compressor and you will hear a faint 'click' when the thermostat cuts in and out. Energy Saving Advice Do not install the appliance close to sources of heat, such as a boiler or radiator. Locate the appliance in a cool well ventilated room and make sure that the air openings of the appliance are not obstructed. Avoid unnecessary frosting in the cabinet by packing all foodstuffs into airtight packages before placing them in the freezer compartment. Food which is to be frozen (when cool) should be placed in the fridge compartment before being transferred to the freezer compartment. Try to avoid keeping the door open for long periods or opening the door too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often. Ensure there are no obstructions preventing the door from closing properly. Food Storage To obtain the best performance from your appliance: Do not store warm food or evaporating liquid. Avoid buying frozen food if you cannot store it straight away. The use of an insulated container is advisable. When you arrive home, place the frozen food in the freezer compartment immediately. Ensure that food placed in the freezer compartment is dated and labelled and used in date order to ensure that food is consumed at its best. This frost, which acts as an insulator and thus prevents the cold from reaching the food should be removed whenever the thickness of the frost exceeds 6 mm (1/4). To carry out complete defrosting proceed as follows: 1. Remove any food from inside the ****-star compartment, wrap it in several sheets of newspaper and store in a cool dry place. Turn the thermostat knob to position << 0 >>. To accelerate defrosting, place a bowl of hot water inside the compartment (with a piece of cardboard underneath the bowl as protection). Remove any loose pieces of ice as soon as possible. 9 Changing the Light Bulb Should the light fail to work you can change it as below: Disconnect the appliance from the electricity supply. Remove the lamp cover retaining screws, then take the lamp cover off in the direction of the arrow and the bulb can be changed. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working. " When you contact the Service Force Centre you will need to give the following details: 1. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls. Cus t omer Car e Depar tment For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the adresses below or visit our website at www. zanussi. co. uk Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) *calls to this number may be recorded for training purposes. 11 Guar ant ee Conditions We Zanussi undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electrical supply stated on the rating plate. [. . . ] Slide the worktop towards the rear and lift clear of the appliance. Remove the 2 upper hinge plate retaining screws. Remove the hinge plate from the top of the door. Unscrew the hinge pin from the hinge plate and reinsert on the opposite side of the pate. Rotate the hinge assembly 180° and insert the hinge assembly into the opposite location. [. . . ]