User manual ZANUSSI ZU5120F

[. . . ] The appliance must not be located close to radiators or gas cookers. Avoid prolonged exposure of the appliance to direct sunlight. There must be adequate ventilation round the back of the appliance and any damage to the refrigerant circuit must be avoided. For freezers only (except built-in models): an ideal location is the cellar or basement. [. . . ] It is advisable to wait at least two hours before connecting the appliance to allow tlie oil to flow back in the compressor. s This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from your municipal authorities. The materials used on this appliance marked with the symbol are recyclable. s s s CONTENTS Installation s s s s s s GB 41 41 42 42 42 42 42 36 36 36 37 37 38 39 s s Positioning the door shelves Defrosting Positioning Cleaning the interior Location Door reversibility Fitting a decorative door panel Electrical connection Maintenance s s s Periodic cleaning Extended periods of non-operation Interior light Defective operation Technical specification Use s s s s 39 40 40 40 40 40 35 Operation Temperature regulation Fresh food refrigeration Movable shelves INSTALLATION If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child. GB Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brandnew product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special " Building-in" instructions given. Important It is essential that the appliance be connected to an efficient earth tap. For this purpose the supply cable plug incorporates a special earth contact. 5 A = = D467 37 Fitting a decorative door panel Important :The components needed to fit the decorative panel have been pre-fitted on the appliance. The brackets are secured to the panel by means of the 7 Ø 3. 5x13 screws supplied. Before starting to fit the panel, remove the large top bracket by unscrewing the screws and adjusting pins prefitted on the appliance door. The small bottom bracket need not be removed. Position the top bracket on the panel, making sure that there is an equal distance between it and the sides and that its distance from the top edge is equal to distance (A) less 1 cm. Secure the bracket with the screws supplied. Take care not to damage the front face of the panel whilst working. 7) into their locations in the door and screw them in. 8 Hook the decorative panel onto the top part of the door, inserting the pins (B) (on the door) into the elongated holes (1) (in the top bracket fitted to the panel) (Fig. Insert the securing screws (C) through elongated holes (2) and fix the panel without tightening the screws (Fig. 9 Once the top of the panel has been correctly positioned, fix it through the holes in the bottom bracket, without tightening the screws (Fig. [. . . ] Milk bottles: these should trave a cap and should be stored in the bottle rack on the door. Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator. Temperature regulation The temperature is automatically regulated and can be increased to achieve a higher temperature (warmer) by rotating the thermostat knob toward lower settings or reduced (colder) rotating the knob towards higher settings. However, the exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on: room temperature; how often the door is opened; the quantity of food stored; location of appliance. A medium setting is generally the most suitable. [. . . ]