User manual ZANUSSI ZUD9124

[. . . ] REFRIGERATOR ZUD 9124 INSTRUCTION BOOKLET 2222683-32 CONTENTS Instructions for the User Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration The door shelves The -star compartment Freezing fresh food Frozen food storage Thawing Making ice cubes Normal Operating Sounds Instructions for the Installer 3 4 5 5 5 5 5 6 6 6 6 6 6 Technical Specifications Installation Positioning 15 15 15 Electrical Connection Building-in Instructions Inner door reversal Grid preparation Door reversal Building the appliance in under a worktop Fitting the plinth 16 17 17 17 18 19 23 Health and Safety Guidelines Defrosting Maintenance and Cleaning Internal cleaning Periodic cleaning Changing the light bulb When the appliance is not in use 7 8 9 9 9 9 9 Something Not Working?Service and Spare Parts Customer Care Department Zanussi Service Force Guarantee Conditions 10 11 11 12 14 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings or these warnings contact the Customer Care Department. Prior to Installation s General Safety s Check the appliance for transport damage. [. . . ] remove any stored food, wrap it in several layers of newspaper and put it in a cool place; 3. leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, remove the plug as shown in the figure; 4. when defrosting is completed, dry the interior thoroughly and refit the plug. Keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. P F S. I. 011 PR151 8 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Warning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Zanussi Service Force centre). Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. D411 2. Replace the light cover by sliding it into its original position and replacing the screw. Periodic cleaning The appliance is equipped with a ventilation grid. Keep clean to guarantee good ventilation and good working order of the appliance. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. The structure of the appliance permits to clean the rear zone close to the wall, using a vacuum cleaner. Remove the plinth (1), then the ventilation grid (2); 2. Carefully pull the air deflector out (3), checking that there is no water left from the defrosting. 3 2 1 S. I. 013 When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. 9 SOMETHING NOT WORKING? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom No power to appliance Solution - Check there is power at the socket. - Check there is not a power cut by checking the household lights. - Ensure that the bulb is correctly fitted. - Check the door light switch is not jammed. [. . . ] Refit the door and insert the top pin and bottom bracket (1), pushing it into place. To ensure correct storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. 180° 2 1 PR140 Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). A B Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure). DO002/2 To position the grid on the appliance proceed as follows: Apply the grid to the base of the appliance by pushing on to the clasps (a) until they click. a a DO001 17 Door reversal To reverse the opening direction of the door, proceed as shown in the figures: 6 4 1 7 8 5 2 3 1 2 10 13 9 12 11 3 Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. [. . . ]