User manual ZANUSSI ZVC200S

[. . . ] Children should not be allowed to tamper with the controls or play with the product. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used. It is dangerous to alter the specifications or modify this product in any way. [. . . ] The supply-lead plug in fact incorporates a special earth or ground contact for this purpose. If by any chance the sockets of your domestic wiring system are not earthed, the appliance must be connected to a separate earth or ground wire by a qualified electrician, in accordance with existing safety regulations. The manufacturer declines to accept any liability if this accident-prevention procedure is not followed. directive number 87/308 of 2. 6. 87 relative to radio interference suppression. A B D425 Rear spacers In the plastic envelope containing the Operating Instructions two wall spacers are also included which should be fitted into the special openings provided on the back of the appliance. Push-fit the spacers into the openings, making sure that arrow (A) is positioned as per Fig. 2 and then turn the spacers through 45° until they lock in (arrow in vertical position). This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Cleaning the appliance's interior Before using the appliance for the first time, wash all internal parts with lukewarm water and neutral soap so as to remove the typical «new» smell and then dry thoroughly. Do not use detergents or abrasive powders as these will damage the finish. 34 Door reversibility Unplug the freezer before performing the following operations: Remove the ventilation grill (D-Fig. 3) by loosening the two fastening screws. 3 Remove the handle and refit it on the opposite side (Fig. 5 E F G G D162 D F D071 The holes that are not used are to be masked with the plastic plugs removed. If, after having reversed the door, it is not in line with the unit, the top hinge can be adjusted. To do this, use a 10 mm spanner as shown in Figure 4; slacken the nut, align the door by pushing it to the left or right, then re-tighten the nut. Attention After completion of the door reversibility operation, verify that the door gasket is adherent to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. Remove the door by sliding it out of the upper pin (A-Fig. Unscrew the pin and the washer (A+B-Fig. 3) on the opposite side by means of the two screws that have been previously removed. 3) from the ventilation grill (D) pushing it as shown by the arrow. Fit the plastic plug (G) supplied with the appliance, in the seat left free on the opposite side. Refit the ventilation grill. 35 USING YOUR FREEZER This freezer has been marked with the symbol, which means that it is suited to the freezing of fresh foods, the conservation of frozen foods and the production of ice-cubes. The control panel (Fig. [. . . ] If a thick layer of ice is formed it will be necessary to carry out complete defrosting as following: set the knob (E) to «O» position or unplug the appliance from the mains socket; wrap frozen food in several layers of newspaper and place the food packages in a cool place; leave the door open. Introduce the plastic scraper in the appropriate seating at the bottom center, as shown in figure, place underneath a basin to collect the defrost water. 9 D068 Cold accumulator A cold accumulator is supplied in the freezer; this increases the length of time for which food will keep in the event of a power failure or breakdown. It must be placed in the top drawer (Fig. [. . . ]