User manual ZANUSSI ZWH7100C

[. . . ] User Manual Washing machine ZWH 7100 C Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - -6-8 Programme table - - - - - - - - - - - - - - - - -9-10 Programme information - - - - - - - - - - - - - -11 Washing Hints - - - - - - - - - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -14 Operating Sequence - - - - - - - - - - - - - - - -15 Care and cleaning - - - - - - - - - - - - - - - - - -18 Something not working - - - - - - - - - - - - - - 20 Technical data- - - - - - - - - - - - - - - - - - - - - 23 Consumption values - - - - - - - - - - - - - - - - 24 Installation instruction - - - - - - - - - - - - - - - 25 Environmental concerns - - - - - - - - - - - - - 28 2 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. [. . . ] If you have already pressed it, and you wish to cancel the delay time, proceed as follows: · set the washing machine to PAUSE by pressing button 8; · press the button 10 once. On the display will appear the symbol «0'». · press button 8 again to start the programme. · If the programme has already started, the selected delay can be modified only after you have turned the programme selector dial to the «Off» position and after you have selected the programme again. · The door will be locked throughout the delay time. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 8, the pilot light 9 goes off and the door can be opened. After you have closed the door, press the same again. The Delay Start cannot be selected with «Drain» programme. 16 Display The display shows the following information: After selecting a programme the duration of the selected programme appears on the display. During the programme, the time remaining is updated every minute. 2. 00 The Delayed start appears on the display for about 3 seconds, then the duration of the previously selected programme is displayed. The delay time value decreases by one unit every hour and then, when 1 hour remain, every minute. The incorrect option selection is indicated by the message Err displayed for few seconds and by flashing of the red light button 8. In the event of operating problems, some alarm codes can be displayed, (see paragraph "Something not working"). E20 The End of programme or the stop with water in the tub is indicated by a flashing zero «0». 0 Altering an option or a running programme It is possible to change some option before the programme carries it out. Before you make any change, you must pause the washing machine by pressing button 8. Changing a running programme is possible only by resetting it. Turn the programme selector dial to «Off» and then to the new programme position. Start the new programme by depressing button 8 again. The washing water in the tub will not empty out. Interrupting a programme Depress the button 8 to interrupt a programme which is running, the corresponding light starts to flash. Depress the button again to restart the programme. Cancelling a programme Turn the selector dial to «Off» to cancel a programme which is running. Opening the door after the programme has started First set the machine to pause by pressing the button 8. If the light 9 goes off, the door can be opened. [. . . ] A minimum water pressure of 0. 05 MPa (0. 5 bar) is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum vertical distance of 5. 02m (16. 5 ft) between the appliance's inlet and the bottom of the water storage tank. If the outlet spigot has not been used before, remove any blanking plug that may be in place. [. . . ]