User manual ZEKTOR CVS4

[. . . ] ZEKTOR Ho m e T h e a t e r Switches Digital Video / Component Video / Multichannel Audio CVS4 High Definition Component Video Switch Rev 2 07/26/2006 Contents What's Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 An Overview of the CVS4 . . . . . . . . . . . . . . . . . . . . 7 More Remote Options . . . . . . . . . . . . . . . . . . . . . . . . 9 Controlling the Front Panel Lights . . . [. . . ] The sequence is: Standby '1' - LED '2' - LED '3' - LED '4' - LED Standby Standby Standby LED Waiting Waiting Waiting Waiting Waiting Waiting Waiting Waiting for for for for for for for for Power Toggle IR code. input sequence code. 1 2 3 4 POWER The IR LED will flash. . . . . . and the LEDs will sequence each time a remote control button is pressed if the IR code is compatible with the CVS4. 1 4 7 2 5 8 0 3 6 9 + _ VOL + _ CH & '1' LEDs & '2' LEDs & '3' LEDs Skipping or Deleting IR codes I f the LEDs do not sequence, and the IR LED does not flash, when a button is pressed on the remote, then the C VS4 does not recognize the IR code being sent. M ake sure the remote's batter ies are fresh. The C VS4 will wor k with most remotes, however there are a few exceptions. S ome technical reasons for not wor k ing with some re motes are: The remote may be using a car r ier frequenc y outside the range of the C VS4 (4KH z to 42KH z), or it may be using one of the few protocols the C VS4 does not understand, like the Philip's RC and RC6 protocols. 1 2 3 4 POWER 1 4 7 2 5 8 0 3 6 9 Skip current code (Leave IR unchanged) Disable IR for current function being learned. I f the C VS4 does not lear n the remote codes you are using, you will have to use another remote, or in the case of using a universal re mote, you'll have to pick a different manufac turer's code. Skipping or Deleting IR codes Dur ing the IR lear ning process you can choose to delete the cur rent code (disable IR for that func tion) or sk ip the cur rent code (leave it unchanged) by pressing the '' or '4' buttons: '3' '4' Disable IR for cur rent func tion. Sk ip cur rent code, leave it unchanged. + _ VOL + _ CH CVS4 Component Video Switch CVS4 Component Video Switch Step 1: Place the CVS4 into the Setup Mode 1 2 3 4 Controlling the Front Panel Lights There are four different front panel light modes available on the C VS4. They are: Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. Note: · · · · Front panel lights af ter 4 seconds of Front panel lights Front panel lights Front panel lights automatically fade from br ight to dim inac tivit y. are tur ned off. Step 2: Select "Lighting Mode" option 1 2 3 4 The intensities of the both the br ight and dim levels can be adjusted as well, this is explained in the nex t chapter. To change the front panel lighting mode. . . Step 1: Enter the Setup Mode · · · The C VS4 is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the `' button to selec t the "Lighting M ode" option. The front panel selec tion LEDs now indicate the cur rently selec ted light mode as follows: I f `' is lit, then front panel lights are always off. I f `2' is lit, then front panel lights are always dim. I f `' is lit, then front panel lights are always br ight. I f `4' is lit, then front panel lights auto -fade from br ight to dim af ter 4 seconds of inac tivit y. Choose a new light control mode by pressing the associated selec tion button. When powered up by pressing the Power button, it will retur n to that previously selec ted channel. However, if power is removed (for instance a plug str ip used to power the C VS4 is tur ned off ), and then re -applied, the C VS4's default behavior is to enter into the standby mode. I t is possible to change the power on behavior of the C VS4. To change the power on defaults. . . 1 2 3 4 Setup the CVS4 to the initial power on state you'd prefer. Step 1: Setup the CVS4 to your preferred power on state. · Use the front panel buttons to setup the C VS4 to the operating settings you'd like at initial power up. While continuing to hold the Power button, press and hold the `' button. Af ter holding both buttons for about `4' seconds, the display will blink indicating the new power on defaults have been accepted. [. . . ] D. C. 24 CVS4 Component Video Switch CVS4 Component Video Switch 2 Thispagelef tintentionally(nea rl y)blank. Thispagelef tintentionally(nea rl y)blank. 26 CVS4 Component Video Switch CVS4 Component Video Switch 27 Warranty Policy Warranty Policy ZEK TOR war rants this produc t against defec ts in mater ial and wor kmanship under nor mal use and ser vice for t wo years from the or iginal date of purchase. ZEK TOR, at its option, shall repair or replace the defec tive unit covered by this war rant y. I n order to keep this war rant y in effec t, the produc t must have been handled and used as prescr ibed in the instruc tions accompanying this war rant y. This war rant y does not cover any damage due to accident, misuse, abuse, or negligence. [. . . ]