User manual ZEKTOR MAS3

[. . . ] ZEKTOR TM MAS3 Multi-channel Audio Switch Owner's Manual www. zektor. com Rev: 2 03/12/04 Important Safety Instructions! Read all instructions for prior to installation of your product. Retain this User's Manual for future reference. Adhere to all safety and operation instructions. Before cleaning this product, unplug from the wall outlet. [. . . ] Or teach the MAS3 a new set of codes, See: "Learning New Remote Codes" on page 8. Teaching the MAS3 a new component code After your remote control has been programmed to act like one of the 8 built in code-sets, teaching the MAS3 to use the new code set is simple. 6 STEP 1 ZEKTOR 1 2 3 1 Place the MAS3 in standby mode. This is the factory default mode on power up, and if it has not been changed, you can unplug the MAS3 and plug it back in and it will power up in standby mode (at this point only the power indicator light is lit and glowing RED). If the MAS3 does not power up in standby mode, follow the steps given in "Restoring the MAS3 to Factory Defaults" on page 13. 2 On your remote control press the buttons in the following sequence, after each button press verify that the remote IR indicator flashes. (If you make a mistake, you can start over by pressing POWER twice. ): · POWER · CHANNEL + · POWER · CHANNEL 3 The MAS3 will power up indicating the new component codes have been accepted. STEP 2 ZEKTOR 1 2 3 STEP 3 ZEKTOR 1 2 3 Searching for a component code in your remote Assuming you do not have a remote listed in this user manual you will have to follow your remote controls programming sequences to find a compatible component that the MAS3 understands, or you can go to the section "Learning New Remote Codes" on page 8, to teach the MAS3 new keys for individual commands. To search for compatible component codes you must place the MAS3 in standby mode and try manufacturer codes in your remote control until one of them causes the MAS3's IR indicator LED to flash. STEP 1 ZEKTOR 1 2 3 1 Place the MAS3 in standby mode. This is the factory default mode on power up, and if it has not been changed, you can unplug the MAS3 and plug it back in and it will power up in standby mode (at this point only the power indicator light is lit and glowing RED). If the MAS3 does not power up in standby mode, follow the steps given in "Restoring the MAS3 to Factory Defaults" on page 13. 2 Try different manufacturer codes until one of them causes the IR indicator light on the MAS3 to blink when pressing the POWERTOGGLE key. When found, go to back to "Teaching the MAS3 a new component code" on page 6, to teach the MAS3 to use the new component code. STEP 2 ZEKTOR 1 2 3 7 Learning New Remote Codes Teaching the MAS3 to use new remote control keys If your remote does not have one of the pre-programmed component codes, or you simply want to re-map the MAS3 functions to other keys on your remote, the MAS3 can be taught to use new keys. To teach the MAS3 to respond to new keys, you need to have the remote control(s) you want to use ready, and setup in the manner you want it to be used. STEP 1 ZEKTOR 1 2 3 1 Place the MAS3 in standby mode. This is the factory default mode on power up, and if it has not been changed, you can unplug the MAS3 and plug it back in and it will power up in standby mode (at this point only the power indicator light is lit and glowing RED). If the MAS3 does not power up in standby mode, follow the steps given in "Restoring the MAS3 to Factory Defaults" on page 13. 2 Using a pen or pencil, press and HOLD the SETUP button on the back panel of the MAS3 (located near the power jack) for around 4 seconds, until the MAS3 powers up, and the Power indicator on the front panel of the MAS3 will turn GREEN and begin to blink RED. The MAS3 is now ready to accept new remote control key codes. For each of the following steps: STEP 2 ZEKTOR 1 2 3 ZEKTOR 1 2 3 · You may press a key on your Remote Control, if accepted, the IR indicator light will blink, and the key will be learned as the new key for the given function. · Or you may press and release the SETUP key on the back panel of the MAS3, this indicates to the MAS3 to skip this key, and the whatever key was previously programmed for that function will be retained. · Or you may press and hold the SETUP key on the back panel until the MAS3 returns to standby mode. This will end learn mode, all keys already programmed will be remembered, and all the keys skipped will retain their previously programmed values. [. . . ] The MAS3 factory defaults, are: · Control codes used are the Symphonic TV codes. · Default power up mode is standby. · Default selected input when powered on is input 1. · Default brightness mode is Auto-dimming. STEP 2 ZEKTOR 1 2 3 STEP 3 ZEKTOR 1 2 3 13 Typical Application Typical application of Multi-channel Audio Switching SACD player MAS-3 L SUB L 1 L SUB L 2 L SUB L 3 OUTL SUB L DC input R CENTER R R CENTER R R CENTER R R CENTER R SACD Player # 2 To 6 channel Pre-Amp DVD-A Player 14 Warranty Information Warranty Policy ZEKTOR, LLC warrants this product against defects in material and workmanship under normal use and service for one year from the original date of purchase. [. . . ]