User manual ZENEC ZE-5.1D

[. . . ] 5. 1 DIGITAL AMPLIFIER WITH AV-PROCESSOR AND OSD MODEL NO: ZE-5. 1D ZE-5. OPERATION MANUAL OPERA INHALT/ CONTENTS Technische Merkmale Eingänge- Ausgänge Funktionen der Fernbedienung Lautsprecheranschluss-Diagramm Stromversorgung Anschluss-Diagramm A/V Anschluss-Diagramm Tipps zur Einstellung / Bedienung Technische Daten Garantiebestimmungen Page 4 5 6­7 8 9 10 11 ­ 14 27 28 Technical Features Inputs ­ Outputs Remote Control Buttons Speaker Connection Schematic Operation Power Input Schematic A/V Connection Schematic Operation Guide Specifications Warranty 16 17 18 ­ 19 19 20 20 21 ­ 25 26 28 2 3 ZENEC 5. 1 CHANNEL DIGITAL POWER AMPLIFIER Herzlichen Glückwunsch!Wir gratulieren Ihnen zum Kauf dieser 5. 1 Kanal Digital-Endstufe von ZENEC. Damit Sie die Wiedergabequalität und die Leistungsfähigkeit dieses Verstärkers voll ausschöpfen können, bitten wir Sie, sich eingehend mit den Möglichkeiten und technischen Features dieses Modelles vertraut zu machen. Lesen Sie deshalb die nachfolgenden Abschnitte sorgfältig durch und bewahren Sie diese Bedienungsanleitung für später auftauchende Fragen auf. TECHNISCHE MERKMALE 5. 1-KANAL DIGITAL VERSTÄRKER MIT INTEGRIERTEM DOLY DIGITAL & DTS DEKODER à Ausgangsleistung: 50Wrms x 5 & 50Wrms x 1 @ 4 Ohm (> 0. 2% THD / 13. 8V) à Integrierter Decoder für Dolby Digital 5. 1 & DTS 5. 1 à Intergrierter Pro Logic Dekoder mit 2-CH Stereo / Phantom Mode / Surround Wiedergabe à 24Bit AD/DA Wander für höchte Tonqualität à Digitale Frequenzweiche mit 24dB/Oct. [. . . ] Input Selection The INPUT SELECT button on the remote control provides manual switching of the input coming into the system. The first press of the INPUT button displays the current input source. The selection switches in order from -> Optical -> Coaxial-> Input1 -> Input2 and then back to Optical again. Input switching is possible while the source is displayed on the screen. If there is an error in optical or coaxial input, the display will blink continuously. In this circumstance, all controls are available while blinking. The ZE-5. 1D has source memory: When you power the unit off and then on again, it will remember the last source selected, and return to that source automatically. Test Tone The ZE-5. 1D amp features a test tone mode to check, if all speakers are connected properly. When this button is selected (on the remote control), white noise of a fairly low volume is forwarded to each of the 5 main speakers in order from -> Front Left -> Center -> Front Right -> Rear Right -> Rear Left, alternating every 2 seconds until the button is pressed once more. Note: There is no test tone for the SUB output. Set-Up This button causes the On Screen Display to open the menu for setting up the ZE-5. 1D amplifier. In this menu window, the selection, function, and control of the selected function sections can be accomplished. The Set-Up menu allows control of: · Pro Logic Selection · Dynamic Range Compresion Selection for Dolby 5. 1 material · Crossover Filter selection for LPF and HPF used in Bass Management · INPUT1 Level · INPUT2 Level · Channel level (input gain) control Pressing the Set-Up button on the remote while the menu is displayed on-screen, will cause the menu to hide. This button is also used to return to the main Set-Up menu from the channel level control menu. Menu Up/Down When the menu is displayed on the OSD (On-Screen Display), the function to be controlled can be selected by the Up/Down buttons. The buttons are set up in a circular pattern on the remote, for ease of use. Selection Left/Right After the selection of function using the Menu Up/Down button, function-dependant values can be changed using the LefVRight buttons on the Remote Control. As soon as the value is changed, the new value is displayed without requirement of confirmation. For value changes, the left button is used for decreasing values, and the right button is used for increasing values. 18 7. Enter This button is used to enter the channel level control in the Set-Up menu. Source Display By pushing this button, you can display the decoding mode or Pro Logic mode on the monitor or TV. The following is an explanation of the modes: · Dolby Digital - Input source is Dolby Digital bitstream for all listening modes · Pro Logic - Input source is PCM and Pro Logic is on for phantom or surround modes. [. . . ] This warranty is limited to the repair or the replacement of the defective product at the manufacturer's option and does not include any other form of damage, whether incidental, consequential or otherwise. The warranty does not cover any transport costs or damages caused by transport or shipment of the product. Warranty work will not be carried out unless this warranty certificate is presented fully completed with model, serial number, purchaser's address, purchasing date and dealer stamp together with the original sales slip!2 JAHRE GARANTIE Sehr geehrter Kunde, Vielen Dank, dass Sie sich zum Kauf dieses Produktes von ZENEC entschlossen haben. [. . . ]