User manual ZENITH H27D44DT OPERATING GUIDE

[. . . ] machine numbers H27D44DT, H32D44DT · P res entatio n T M TV s ® table of contents page 5 enjoy the view installation & operating guide / warranty © Copyright 2001, Zenith Electronics Corporation RECORD YOUR MODEL NUMBER The model and serial number of the PresentationTM TV are located on the back of the TV cabinet. For your future convenience, we suggest that you record these numbers here: MODEL NO. ____________________________________ SERIAL NO. ____________________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. [. . . ] Refer to the brand programming codes on pages 34 - 35 to find the type and brand name of the device you're programming. It's recessed so it doesn't get pushed accidentally. When the indicator light turns on, you can release the key. Push the key with the name of the device you're programming (VCR, CABLE, AUX, TV). Using the NUMBER keypad, enter the three-number code found on the charts on pages 34 - 35. Press ENTER to save the code The indicator light will flash three times and turn off if the code was accepted. Point the remote at the device and push the POWER key. If not, try the other codes listed and continue from Step 3. CABLE SURF VCR AUX TV MUTE FLASHBK CHANNEL VOLUME VOLUME 3 4 5 6 7 CHANNEL 1 2 5 8 ENTER 3 6 9 5 4 7 0 6 QUIT MENU A B PAUSE C CC TV/VCR SOURCE Programming your Zenith remote will allow you to use one remote to work up to 7 different devices!Not all devices will work with your Zenith remote control. RECORD TIMER PLAY REWIND STOP FFWD Mode / Product Compatibility TV VCR TVs VCRs CATV Cable Boxes, Satellite Receivers AUX (AUX+1, AUX+2, AUX+3) All products on pp 34 - 35 PAGE 30 206-3602 Amplifier Volume Override Sets up your amplifier to be operated in all remote control modes 3 PRG POWER Indicator Light CABLE VCR AUX TV MUTE 2 SURF FLASHBK 1 Find the code that operates your amplifier. Test it to make sure it's the correct one by following the procedure in "Programming Your Remote" on the previous page. Program your audio system into one of the available AUX modes: Aux, Aux+1, Aux+2, or Aux+3. Press and hold PRG on your remote until the indicator light stays lit, then release. The indicator light will flash three times if the code was accepted. Audio system volume/mute now appears in all modes. Note: You can also program Cable Box Volume and Mute control (if available) into your cable box mode (CABLE or AUX mode) by repeating the steps for programming on the previous page but entering 3-9-9, instead of a brand code, then pressing ENTER. Your volume and mute keys now control your amplifier, while all the other keys still operate the Presentation TV. To put everything back to normal, reprogram all modes with their original codes (see the "Programming Your Remote" page). CHANNEL VOLUME VOLUME 2 3 4 CHANNEL 1 4 7 0 2 5 8 ENTER 3 6 9 4 MENU QUIT A B PAUSE C CC TV/VCR SOURCE RECORD TIMER PLAY REWIND STOP FFWD Mini glossary AMPLIFIER An electronic device that amplifies sound from a television, CD player, VCR, or other A/V device. 206-3602 PAGE 31 AUX+1, AUX+2, AUX+3 There are 3 additional AUX modes you can program 1 2 3 4 5 6 7 Refer to the brand programming codes on pages 34 - 35 to find the type and brand name of the device you're programming. Press and hold the PRG key until the indicator light turns on. Press the AUX key and the 1 on the NUMBER keypad at the same time (for AUX +1). Using the NUMBER keypad, enter the three-number code for the device you've selected. Point the remote at the device and press POWER. Repeat the steps to program AUX+2, and AUX+3. 2 3 PRG POWER 6 CABLE SURF VCR AUX TV MUTE FLASHBK CHANNEL VOLUME VOLUME CHANNEL 1 4 7 0 2 5 8 ENTER 3 6 9 4 5 Programming your Zenith remote will allow you to use one remote to operate up to 7 different devices. Some devices may not work with the Zenith remote control. MENU QUIT A B PAUSE C CC TV/VCR SOURCE RECORD TIMER PLAY REWIND STOP FFWD PAGE 32 206-3602 Remote Control Auto-Find If Programming the Remote did not find your product's code, try this procedure, to automatically find the code for your device. [. . . ] Extended Data Service: Additional program information provided at the discretion of the broadcaster. 206-3602 PAGE 47 Your Zenith PresentationTM TV Warranty Direct-View Color TV Welcome to the Zenith family!We believe that you will be pleased with your new PresentationTM TV. Please read this warranty carefully, it is a "LIMITED WARRANTY" as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U. S. A. ZENITH'S RESPONSIBILITY Service Labor During a period of one year from effective warranty date, Zenith will provide service labor by a Zenith authorized service center when needed, as determined by the Zenith service center, as a result of manufacturing defects. [. . . ]