User manual ZENITH HE20D50DT OPERATING GUIDE

[. . . ] Installation and Operating Guide | Warranty Model Number | H20D50DT | HealthView TM TV table of contents page 5 © Copyright 2001, Zenith Electronics Corporation RECORD THE MODEL NUMBER For Customer Support/Service please call: 1-888-865-3026 www. zenith. com The model and serial number of this HealthViewTM TV are located on the back of the cabinet. For future reference, we suggest that you record these numbers here: MODEL NO. ____________________________________ SERIAL NO. ____________________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. [. . . ] Note: The Blank Channel feature is global. A channel will be blanked in all channel banks. Repeat steps 2, and 3 to program another channel bank. Inactive TV Display (Channel Bank 4) The TV can be set up to be inactive; which would require an attendant using an installer remote to change to a "billable" active channel bank selection: Bank 1, 2, or 3. Note: For institution control of patient-accessible programming, channels in Bank 4 need to be removed. The BLNK (blank) channel function is "global" -- the same channel number is blanked in channel banks 1, 2, 3, and 4. INACTIVE TV PLEASE . CALL ATTENDANT 206-3684 PAGE 25 Managing the Channel Banks Examples of typical channel banks charts Figure 1. Typical channel banks after running Auto Program B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk B Purpose A N K 1 2 3 4 Basic Extend All CTV Other Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 BC A BC A BC A BC A A A A A A A A A A A A A A A A A D A A A D D D A D A A A D A A A D D D A D A A A D A A A D A A A D D A A D D D A D D A A D D A A A = Active D = Deleted BC = Blanked Channel Channel was found during AUTO PROGRAM Channel was deleted using Add/ Del option. Channel was blanked using BLANK channel option (ADD/DEL/BLNK). ADDING / DELETING CHANNELS It is best to do ADD / DEL customizing before doing "BLNK. " AUTO PROGRAM enters the same channels in Banks 1, 2, 3, and 4. AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted. ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4. A channel blanked, is blanked in all channel banks. Channel allocations in tuning bands: BROADCAST: 2 ­ 69 CABLE ­ CATV, HRC or ICC: 1 ­ 125 PAGE 26 206-3491-O Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies) B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 B Purpose A N K 1 2 3 4 Channel Number 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B Purpose A N K 1 2 3 4 Channel Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 B Purpose A N K 1 2 3 4 Channel Number 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 B Purpose Channel Number A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM N K 1 2 3 4 206-3491-O PAGE 27 Installer Menus Use the Installer's Menus to make TV operation adjustments Accessing the Installer's Menu Installer's menus can be accessed by using the optional installer's remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer's Menu, press ENTER again. Changes you make will be stored in nonvolatile memory. The Installer's Menu opens with item 03, POWER MANAGE. Press the SELECT key to sequence through the various items. Or, access an item directly by entering the line number, then pressing MENU. For example, to access the Start Channel option which is on line 11, press 11, then MENU. To change a current setting use the Left/Right ADJ keys. 1480-01 1. 11 01 03 POWER MANAGE 0 Using the Installer's Menu Items 00-24 are immediately accessible only upon entering the Installer's Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below. [. . . ] Extended Data Service: Additional program information if provided by the broadcaster. 300 TO 75 OHM ADAPTER A/V DEVICE ADD AMPLIFIER ANTENNA AUTO PROGRAM DELETE INPUT JACK MONO SOUND OUTPUT SIGNAL TUNER XDS 206-3584-O PAGE 41 Notes PAGE 42 206-3491-O Notes 206-3584-0 PAGE 43 Your Zenith TV Warranty Direct-View Color TV Welcome to the Zenith family!We believe that you will be pleased with your new TV. Please read this warranty carefully, it is a "LIMITED WARRANTY" as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U. S. A. ZENITH'S RESPONSIBILITY Service Labor During a period of one year from effective warranty date, Zenith will provide service labor by a Zenith authorized service center when needed, as determined by the Zenith service center, as a result of manufacturing defects. [. . . ]