User manual ZENITH L13V36 OPERATING GUIDE

[. . . ] Installation, Setup & Operating Guide I Warranty Model Number | L13V36 | LCD TV © Copyright 2003, Zenith Electronics Corporation. RECORD YOUR MODEL NUMBER (For future reference) The model and serial number of your TV are located on the back of the TV cabinet. For convenience, we suggest that you record those numbers here: MODEL NO. _______________________________ SERIAL NO. _______________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] If you have a 300 flat wire, connect the twisted wire to the antenna converter and then connect the converter to the antenna jack on the TV. - When using 75 round cable, do not bend the bronze wire. It may cause poor picture quality. Connecting to an Outdoor Antenna Setup q This type of antenna is commonly used in single family dwellings. Turn clockwise to tighten. VIDEO (MONO) L VIDEO IN AUDIO R ANT IN +75 VHF Antenna UHF Antenna 75 Round Cable Bronze Wire 300 Flat Wire Single Family Home Antenna Converter Antenna jack - In poor signal areas, to get better picture quality, install the antenna as shown to the right. - If antenna is split for two TVs, use signal splitter for connection. VHF UHF VIDEO (MONO) L VIDEO IN AUDIO R ANT IN +75 signal Amplifier 206-3916 16 - After subscribing to a local cable TV service and installing a converter, you can watch cable TV programming. Cable TV Connections INSTALLATION PB PR H/P S-VIDEO VIDEO(MONO) L AUDIO R VIDEO IN L 1 Connections AC INPUT (110-240V) Y ANT IN +75 COMPONENT(480i) DVD/DTV IN 2 1 (R) AUDIO (L) TV VCR VIDEO RF Cable Cable Box Connection Panel 2 Viewing Setup a. Use the tv/video button on the remote control to select TV (Ant In. ) or Video source, depending on connection setup: 1 or 2. - Connection 1: Set cable box switch to 3 or 4 and then tune TV to the same channel number. - Connection 2: Select VIDEO source input to use Audio/Video In connections. b. Select channels with the cable box. - For further cable TV information, contact a local cable service provider. 206-3916 17 VCR Connection and Viewing Setup - In Video mode, TV automatically reverts to TV mode if the fcr button or flashbk buttons are pressed. - See following pages to connect to other A/V external equipment to input jacks on the TV. Connecting a VCR 1 Connections q Connect the audio/video output jacks on VCR to the corresponding input jacks on the TV. AC INPUT (110-240V) Y PB PR H/P S-VIDEO VIDEO(MONO) L AUDIO R VIDEO IN L ANT IN COMPONENT(480i) DVD/DTV IN +75 2 Typical Antennas 1 ANT IN Direct connection ANT OUT S-VIDEO OUT CH3 IN CH4 (R) AUDIO (L) VIDEO VCR Connection Panel 2 Viewing Setup Watching TV programs Turn the TV on and tune to a channel. Watching VCR a. Use tv/video button on the remote control to select TV (Ant In. ) or Video source, depending on connection setup: 1 or 2. - Connection 1: Set VCR switch to 3 or 4 and then tune TV to the same channel number. - Connection 2: Select VIDEO source input to use Audio/Video In connections. b. Insert a video tape into the VCR and press the PLAY button. 206-3916 18 External Equipment Connections Watching External A/V Source q Connect the audio/video output jacks on the external A/V equipment to the corresponding input jacks on the TV. S-VIDEO VIDEO (MONO) L VIDEO IN AUDIO R ANT IN +75 TV Connection Panel Camcorder External Equipment Connection Panel R AUDIO Video Game set L VIDEO 2 Viewing Setup q q Turn on the external A/V equipment. Turn the TV on and use the tv/video button to select Video source. Video tv/video On Remote Control 206-3916 19 INSTALLATION 1 Connections DVD Player Connections - Connect DVD/DTV output jacks to TV's COMPONENT (480i), Y, PB, PR jacks and S-video jack. Connect DVD/DTV audio output jacks to right and left input jacks on TV. 1 Connections AC INPUT (110-240V) Y PB PR H/P S-VIDEO VIDEO(MONO) L AUDIO R VIDEO IN L ANT IN +75 COMPONENT(480i) DVD/DTV IN TV Connection Panel Y PB PR (R) AUDIO (L) or S-VIDEO (R) AUDIO (L) DVD Connection Panel Note: TV INPUT Y PB PR DVD OUTPUT Y Y Y Y Cb B-Y Pb PB Cr R-Y Pr PR 2 Viewing Setup Turn on the DVD player. Turn the TV on and use tv/video button to select Component source. q See DVD user's manual for operating instructions. q q Component tv/video 206-3916 20 DTV (Set-top Box) Connections - Connect DVD/DTV output to COMPONENT(480i), Y, PB, PR jack inputs on the TV. Connect DTV L/R audio outputs to the TV's AUDIO L/R input jacks. Note: DTV set-top box is required to receive DTV programming. AC INPUT (110-240V) Y PB PR H/P S-VIDEO VIDEO(MONO) L AUDIO R VIDEO IN ANT IN L +75 COMPONENT(480i) DVD/DTV IN TV Connections Panel Y PB PR (R) AUDIO (L) DTV Receiver (Set-top Box) Connections Panel 2 Viewing Setup q q Turn on the DTV receiver (Set-top Box). Turn the TV on and use tv/video button to select Component source. Component tv/video On Remote Control 206-3916 21 INSTALLATION 1 Connections Turning the TV On TV Operation Overview 1 2 3 1 2 3 First, connect antenna cable and power cord correctly. At this moment, the TV is switched to standby mode. q In standby mode, press the power, ch (D, E), tv·video, multimedia or number buttons on the remote control or ch (D, E), tv·video or on/off on the TV side panel to turn the TV on. Select the viewing source by pressing tv·video or multimedia repeatedly. q Note: See page 25 if you have not EZ Scaned the TV to receive channels in your local broadcast area. After viewing, press the power button on the remote control. The TV screen goes dark and it reverts to standby mode. Watching TV Programs Press power on the remote control to turn the TV on. Use the channel (D, E) or number buttons to select a channel to view. Adjust Volume level. q Volume (G) button increases the sound level. Volume (F) button decreases the sound level. Volume 45 q - If you will be away on vacation, disconnect the power plug from the wall power outlet. 206-3916 22 TV Mode Menus 1 Press the menu button repeatedly to display the available menus shown below. EZ Scan Ch. edit Favorite ch. EZ Video Contrast Brightness Color Sharpness Tint G Clear 85 50 70 50 0 FG DE Move Next Menu DE Move Adjust Menu EZ Audio Balance AVL 0 Off DE Move G Next Menu Language Captions Caption/Text Key lock Parental ctl English Off CC 1 Off Clock Off timer On timer Auto off -- : -- AM Off DE Move FG Adjust Menu DE Move G Next Menu 2 206-3916 Use the channel (D, E) buttons to select a menu option. 23 BASIC FEATURES Menu Language Selection Language 1 Use the menu button to select the menu shown. 3 Use the volume (F, G) buttons to select the language for the menus to appear in. Language Captions Caption/Text Key lock Parental ctl English Off CC 1 Off Language Captions Caption/Text Key lock Parental ctl English Off CC 1 Off DE Move FG Adjust Menu DE Move FG Adjust Menu q Each press of volume (F, G) buttons selects languages in the order shown below. English Español Français 2 Use the channel (D, E) buttons to select the Language option. 4 Press the exit button to save and return to TV viewing. 206-3916 24 Finding/Erasing Channels - For EZ Scan to work, the programming source must be connected to the TV and the TV must be receiving programming signals either over-the-air or from a cable-type service provider. EZ Scan (Channel Search) 1 Use the menu button to select the menu shown below. 3 Press the volume (F, G) buttons to begin the channel search. q EZ Scan Ch. edit Favorite ch. Wait for EZ Scan to complete the channel search cycle before choosing a channel. The TV scans for over-the-air channels and then channels provided by a cable service. DE Move G Next Menu Channel number being memorized is displayed. EZ Scan Stop : A TV 63 34% 2 Use the channel (D, E) buttons to select the EZ Scan option, then press the volume (G) button. EZ Scan FG - When the channel search is complete, use the channel (D, E) buttons to review the memorized channels. [. . . ] Wring the cloth until it's almost dry, and then use it to wipe the screen. Make sure not to put an excessive amount of water on the screen, let it air-dry before you turn on your TV. Cabinet Cleaning 1. Use a soft cloth with a mild soap solution to wipe the cabinet. Rinse the cloth and wipe the cabinet again. [. . . ]