User manual ZENITH P42W22B OPERATING GUIDE

[. . . ] Please read this operating guide carefully before using the Monitor. Keep the operating guide with the Monitor. For future reference, write down the serial number on the back of the Monitor in the space provided below. PLASMA DISPLAY PANEL Model number : Serial number : P42W22 P42W22B OWNER'S MANUAL P/NO : 3828VA0296L (NF01DC) 206-03788 ON/OFF INPUT SELECT VOLUME Colored dots on the screen A PDP (Plasma Display Panel), depending on its size, contains from 0. 9 to 2. 2 million individual cells. Even with advanced technology it is inevitable that a few defective cells may be found in the PDP. [. . . ] VIDEO S-VIDEO COMPONENT Connections COMPONENT source only works in 480i mode. Basic operation PIP INPUT F VIDEO G Sleep timer Moving the PIP (inset) picture position Picture & Sound Press the position button in PIP mode. · Each press of the position button will move the PIP picture on the screen as shown below. Special features Others 27 Picture In Picture (PIP) function Selecting sound source with PIP on - To hear main source or PIP (inset) sound source. - This function only works with the following resolutions; 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz). - To use this function, connect PC/DTV video output to RGB-PC INPUT/RGB-DTV INPUT and connect PC/DTV audio output to AUDIO INPUT on the monitor. READY Press the menu button and then use the up/down button to select the SPECIAL menu. Press the vol ( G ) button. menu up vol down 1 2 3 Use the up/down buttons to select PIP and then press the vol ( G ) button. up vol down SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G G G TO SET Use the up/down button to select SOUND SELECT and then press the vol ( G ) button. up vol down LANGUAGE CAPTION PIP AUTO OFF INPUT SCREEN SOUND SOUND SELECT RGB-OUTPUT POSITION G G G G G G G G SOUND [M] G SOUND [S] Use the up/down buttons to select main picture sound (SOUND [M]) or PIP picture sound (SOUND [S]) and then press the enter button. · Each time you press the up/down button, you toggle between SOUND [M] or SOUND [S]. up enter down LANGUAGE CAPTION PIP AUTO OFF INPUT SCREEN SOUND SELECT RGB-OUTPUT POSITION G G G G G G G G SOUND [M] G SOUND [S] SOUND [S] 28 Safety instructions Monitor Overview Remote Control Setup Installing batteries · Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match "+" with "+", and match "-" with "-". · Install two 1. 5V "AA" alkaline batteries. Don't mix used batteries with new batteries. Connections Basic operation Sleep timer Notes for using the remote control Make sure these are no objects between the remote control and its sensor. Don't place the remote control near a heater or damp place. Strong impact on the remote control may cause operation failure. Signal from the remote control may be disturbed by sun light or other strong light. In this case, turn the set to other direction. Picture & Sound Special features Others 29 Turning on the Monitor - When using the remote control, aim it at its sensor on the Monitor. Turning on the Monitor just after installation 1 2 Plug power cord into power outlet correctly. Press the main ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the or INPUT SELECT button on the Monitor or press power on or video/pc button on the remote control to turn the Monitor on. Turning on the Monitor (power cord is still connected) 1 2 3 If the Monitor is turned off with the button on the Monitor Press the or INPUT SELECT button on the Monitor or press the power on or video/pc button on the remote control to turn the Monitor on. If the Monitor is turned off with the ON/OFF button on the Monitor · Press the main ON/OFF button on the Monitor to turn the Monitor on. If the Monitor is turned off with the remote control and also the ON/OFF button on the Monitor · Press the main ON/OFF button on the Monitor and then press the or INPUT SELECT button on the Monitor or press the power on or video/pc button on the remote control to turn the Monitor on. Tip · Adjusting sound level The volume (G) button increases the sound level and the volume (F) button G F decreases the sound level. 30 Safety instructions Monitor Overview Menu Language Selection READY Press the menu button and then use the up/down button to select the SPECIAL menu. Press the vol ( G ) button. menu up vol down Connections Basic operation 1 Use the up/down button to select LANGUAGE and then press the vol ( G ) button. up vol down SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G G ENGLISH ESPAÑOL PORTUGUÊS FRANÇAIS Sleep timer Picture & Sound 2 Use the up/down button to select the desired language. up SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G G ENGLISH ESPAÑOL PORTUGUÊS FRANÇAIS down Special features 3 Press the enter button to exit. Others enter 31 Checking Features - Use the remote control to make adjustments. - Select VIDEO input source menu 1 2 Press the menu button. Press the up/down button. · Each press will cycle through the menus shown below. PICTURE APC DRP CONTRAST BRIGHTNESS COLOR TINT SHARPNESS D MOVE E G G up down 100 50 50 0 50 G G G G G GNEXT AEXIT Picture Menu SOUND DASP AVL TREBLE BASS BALANCE G G G G G 50 50 0 D MOVE E GNEXT AEXIT Sound Menu SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. D MOVE E G G G G G G G GNEXT AEXIT Special Menu - The Color Temperature adjustment is only available on model P42W22B. up vol down vol 3 Use the vol ( G ) button to select menu option to adjust, and then use the up/down or vol buttons to adjust the selected option. · Press the enter button to exit. 32 Safety instructions Monitor Overview Setting Sleep Timer Sleep Timer turns the Monitor after the preset time expires sleep Use the sleep button to set a sleep time. Each time you press the sleep button, the time setting time changes as follows: F --- G F 240 G F 180 G F 120 G F 90 G F 60 G F 10 G F 20 G F 30 G Connections Basic operation SLEEP F 30 G Sleep timer · To cancel sleep time setting, press the sleep or F / G button repeatedly to select F --- G. ·` SLEEP 1' will be displayed one minute before the Monitor is due to turn off. Picture & Sound Special features Tips · When the sleep time you want is displayed on the screen, don't press the sleep button. After 20 seconds, the screen display disappears and sleep time is set. · To check remaining sleep time after setting, press the sleep or enter button just once. · If you turn the Monitor off after setting the sleep timer, the setting is erased. The sleep timer will then have to be set again. [. . . ] PIP sound select (Command:u) G To select main or sub (inset) sound for PIP. You can also select sound select in PIP on the special menu. Transmission [u][ ][Set ID][ ][Data][Cr] Data 0 : Main picture sound 1 : Sub picture sound Acknowledgement [Set ID][:][OK][x][Data][x] Data 0 : Main picture sound 1 : Sub picture sound * COMPONENT source only works in 480i input signal. 18. Change into Remote control adjustment mode (Command:j) G To control the Monitor with the remote control while the cable is still connected. [. . . ]