User manual ZERO88 SIRIUS 48 EDITION 4

[. . . ] Zero 88 Sirius Lighting Desks Step-by-Step Guide ZERO 88 SIRIUS 24 & 48 Lighting Desks Step-by-Step Guide 4th Edition Zero 88 Sirius Lighting Desks Step-by-Step Guide Hello User, Welcome to this 4th edition of the Sirius Lighting desks step by step user guide. The original operators guide that comes with the Zero 88 Sirius Lighting desks can be a little confusing, especially to one who is not sure of the basic functions and operation of the Sirius Lighting Desks. This step by step guide is aimed at making the programming and running of the desk a lot easier, even for the most simple minded when it comes to electronics and computers. If this booklet is used in the correct way, the programming and running of shows should be come as easy as 1-2-3, quite literally. [. . . ] Make any alterations Turn the KEYSWITCH to `PROGRAM'. Make sure the correct memory is selected. Press the `PROGRAM MEMORY' button. vii) viii) ix) x) 1. If a single or few channels are to be altered then those levels can be changed without having to re-program the whole memory. i) Turn the KEYSWITCH to `PROGRAM'. ii) Select the memory you wish to edit using MEMORY + & - buttons. iii) Put PRESET `B' master to 10 iv) Put the faders of the channels you wish to edit to the new position. v) Press the FLASH buttons of the channels you have changed. Zero 88 Sirius Lighting Desks Step-by-Step Guide 1. Chases can be programmed in so that a sequence of lights can be programmed, either to sequence automatically, or to the beat of music, via the `AUDIO INPUT' on the back of the desk. To program the chase i) Turn the KEYSWITCH to `PROGRAM'. ii) Press the `PREVIEW' button in the EFFECTS area on the left of the desk. The effects section moves through a series of steps, programmed by you i) Set-up the first STEP on PRESET B, making sure MASTER B is at the correct level ii) Press the `PROGRAM STEP' button iii) Press the `ADD STEP' button. iv) Set-up the next step on PRESET B v) When you are happy with that step, press the `PROGRAM STEP' button again. vi) Continue to program further steps, by following steps iii) to v). vii) When you have finished, turn the KEYSWITCH to RUN. 3. 1. 2. i) Turn the KEYSWITCH to `RUN', if it is not already there ii) Using the `EFFECTS' + & - buttons, select the chase you wish to run. iv) Move up the `EFFECTS MASTER' fader to the desired level. There are a number a changes to make to the chase, these do the following. i) The button with three LED's next to it labelled "AUTO" "VARY SPEED" "BASS" changes the type of speed at which the chase runs. Using "AUTO", the chase will run at the speed that is selected by the SPEED control knob in the EFFECTS section. Using "VARY SPEED" the chase will run at different speeds. Using "BASS" the chase will only move on a step, if there is an audio input, and the music is playing, with a decent bass rhythm. ii) The button with three LED's next to is labelled ">. " "<. " "< >. " Changes the direction that the steps follow each other in sequence. The ">. " Sign means that the chase will run forwards, in the order that you programmed the chase. [. . . ] v) When you have finished turn the keyswitch to `RUN' 3. Move the master up and down to control the light(s). 4. You will have to transfer the memories, each time you enter `RUN' mode from `PRESETS ONLY', or when you switch on the desk. 1. `Recovery' mode is an excellent `Super User' function that in the event of a power failure, or power to the desk being lost for some reason, the desk will automatically return to the same scene and setup that is was at when the power is returned. 2. i) Turn the KEYSWITCH to `PRESETS ONLY' ii) Enter `SUPER USER' mode, by pressing and holding the EFFECTS + & - buttons and turning the KEYSWITCH to `PROGRAM' iii) Release the EFFECTS + & - buttons. iv) Find the screen `OTHER THINGS' by using the MEMORY + & - buttons. [. . . ]