User manual ZIBRO SRE 270TC

[. . . ] SRE 270 TC 3 2 6 5 4 > 1 : TR MANUEL D'UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO OPERATING MANUAL ISTRUZIONI D'USO GEBRUIKSAANWIJZING INSTRUKCJA OBSLUGI KULLANIM KILAVUZU 2 12 22 32 42 52 62 72 82 Dear Sir, Madam, Congratulations with your purchase of the Zibro, the number one brand among movable heaters. You have purchased a first-class quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your Zibro. [. . . ] First press either of the two keys to switch on the function (the TEMP light next to the information display will start blinking). Next, adjust the temperature using the key on the right (Mmin) to set the temperature to a higher setting and the key on the left (Nhour) to lower the temperature. Press once to increase the value one step. After approximately 10 seconds the light will stop blinking and the setting will be locked (Fig. G). 4 46 The available temperature settings range from 6C minimum to 28C maximum. When the heater has been unplugged for more than 10 minutes (or after a power failure), the temperature will reset to the factory setting of 20C. F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time. In order to switch on the timer, the correct time must have been set (refer to Section C) and the heater should be off. Follow the procedure below: 1 Press the button and then the TIMER key immediately after that. The TIMER light on the operation panel will start blinking. 2 Use the adjustment keys to set the time at which the heater must ignite. Use the key on the left (Nhour) to set the hours and the key on the right (Mmin) to set the minutes (interval of 5 minutes). 3 After approximately 10 seconds the information display will show CLOCK again and the TIMER indicator light will light up, indicating that the timer function has been activated (Fig. 4 The timer will ensure that the room will have been heated to approximately the required temperature at the set time. H: The TIMER indicator light indicates that the timer function has been switched on. When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. G SWITCHING OFF THE HEATER There are two ways to switch off the heater. The information display will show the CLOCK signal. Within approximately one minute the flame will have extinguished. 2 Press the TIMER key without pressing the button, when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. As long as the TIMER light and the information display are blinking, you can change the required time with the adjustment keys (refer to Section F). H THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (Sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: 4 47 CODE INFORMATION Temperature within the heater too high. Too little ventilation. WHAT TO DO Cool-down and re-ignite. Ventilate better. In case of any malfunctioning the information display will tell you what is the matter. efefeeee- 0 0 1 1 2 5 6 7 e- 8 e- 9 --blinking : -(& FUEL-light) --blinking : -(& VENT-light) Always contact your dealer for any malfunctioning not listed above. AUTOMATIC CLEANING MODE When the heater has been burning continuously for two hours at its highest setting, the burner will automatically start an autoclean procedure. The display will show the autocleaningcode cl:05 running back to cl:01. The procedure takes 5 minutes, during which the heater will burn at its lowest setting, while the burner autocleans. [. . . ] In case of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher. 10 TIPS FOR SAFE USE 1 100 cm 2 20 cm 3 4 50 cm 50 cm 150 cm 5 6 7 8 9 10 Make sure that children are always aware of the presence of a burning heater. Do not move the heater when it is burning or still hot. Do not refill nor service the heater when it is burning or still hot. Position the front of the heater at a distance of minimum 1. 5 metres from walls, curtains, and furniture. [. . . ]