User manual ZIBRO SRE186

[. . . ] Your heater comes with a 24-month manufacturer's warranty on all defects in material or workmanship. We wish you much warmth and comfort with your Zibro Kamin. Yours sincerely, PVG International b. v. Customer Service Department 1 READ THE DIRECTIONS FOR USE FIRST. 2 IN CASE OF ANY DOUBT, CONTACT YOUR ZIBRO KAMIN DEALER. 3 BEFORE YOU START READING, FOLD OUT THE LAST PAGE. 4 42 GENERAL DIRECTIONS FOR USE Below you will find the main steps to be taken for using your Zibro Kamin. For more details, please refer to the MANUAL (pages 45 ff. ). MAIN COMPONENTS Front plate Grid Base plate Lid for removable 1 2 3 4 5 Remove all packaging materials (Fig. tank Fill the removable tank (refer to Section B, Fig. [. . . ] You should therefore provide extra ventilation. Always ignite the heater with the lighter. Just press the button button . Never use matches or a cigarette to ignite the heater. The button will start button will remain lit (red). The blinking, indicating that the ignition procedure has started. Once the heater is burning, the information display will show two numbers. The light next to them indicates that these numbers refer to the temperatures (Fig. The actual room temperature is indicated below ROOM, while the temperature setting is indicated below SET. The latter can be changed with the adjustment keys (refer to Section E). Prior to igniting the heater, always check for sufficient fuel in the removable tank. 19:14 VENT G: The required temperature on the left, the measured temperature on the right. E SETTING THE REQUIRED TEMPERATURE The temperature setting can only be adjusted, when the heater is burning. Use the adjustment keys to adjust the temperature. Refill removable tank. SET ROOM e-: 0 TIMER VENT In case of any malfunctioning the information display will tell you what is the matter. efefeeee- 0 0 1 1 2 5 6 7 e- 8 e- 9 -- : -- (& blinking FUEL-light) Switch the heater back on. Ventilate better. --blinking : -(& VENT-light) Always contact your Zibro Kamin dealer for any malfunctioning not listed above. SET ROOM AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 65 hours continuous operation. The following will then appear in the display: the . If desired, you can switch the heater on again by pressing button (see chapter D). AUTOMATIC CLEANING MODE When te heater has been burning continuously for two hours at its highest SET ROOM setting, the burner will automatically start an autoclean procedure. The display will show the autocleaningcode cl:05 running back to cl:00. The procedure takes 5 minutes, during which the heater will burn at its lowest setting, while the burner autocleans. When the burner is clean again, the heater will automatically switch back to the highest setting again. c l: 0 5 TIMER VENT I CHILDPROOF LOCK The childproof lock can be used to prevent children accidentally changing the heater settings. When the heater is burning and the childproof lock is on, the heater can only be switched off. If the heater FUEL I: When the KEY-LOCK light lights up, the childproof lock has been activated. has already been switched off, the childproof lock also prevents accidental ignition of the heater. Activate the childproof lock by pressing the appropriate key and holding it down for more than 3 seconds. The KEY-LOCK indicator light will light up (Fig. [. . . ] 5 The warranty shall only apply, when you present the original, dated proof of purchase, provided no changes have been made to it. 6 The warranty shall not apply to damages caused by actions not in compliance with the Directions for Use, neglect, and the use of an incorrect type of fuel, or fuel past its use-by date. The use of incorrect fuel can even be dangerous*. 7 Transportation costs and the risks involved during the transportation of the heater or heater components shall always be for the account of the purchaser. [. . . ]