User manual ZOTAC ZBOX ID-42 PLUS

[. . . ] ™™ Set up the system on a stable surface with the provided stand. Never use the system alone without the stand. ™™ Openings on the chassis are for ventilation. Make sure you leave plenty of space around the system for ventilation. [. . . ] To prevent damage to the PC, always use the supplied power adapter.  The power adapter may become warm to hot when in use. Do not cover the adapter and keep it away from your body. 7 ZOTAC ZBOX BIOS settings of specific functions ZOTAC ZBOX has some specific functions which can be enabled or disabled in BIOS settings, such as LED indicator, USB2. 0 charge and CIR controller. How to disable the ring LED indicator 1. Turn on the ZBOX mini-PC, then press <Delete> to enter the BIOS SETUP UTILITY. 2. Use the arrow keys to navigate to the PowerManage menu and select LOGO Indicator. 8 ZOTAC ZBOX 3. Press <Enter> and select Disabled. 4. Press F10 to save the configuration and exit. How to enable USB2. 0 charge (for S3/S4/S5 status) 1. In PowerManage menu, select USB2. 0 S3/S4/S5 Charge Function and press <Enter>. 9 ZOTAC ZBOX 2. Use the arrow keys to enter the item Rear / Front / Top USB2. 0 S3/S4/S5 Charge, and select Enabled. 3. Press F10 to save the configuration and exit. Note: Before charging via USB2. 0 in S5 status, please make sure the Deep S5 (DeepSleep(ErP Compliant) S5 in PowerManage menu) is disabled. 10 ZOTAC ZBOX How to disable CIR controller (for internal IR receiver) 1. Use the arrow keys to navigate to Advanced > OnBoard Device Control > CIR Controller Configuration. 2. Enter CIR Controller and select Disabled. Enabled: enable the internal IR receiver (default) Disabled: disable the internal IR receiver 3. Press F10 to save the configuration and exit. 11 ZOTAC ZBOX Installing Hardware inside ZOTAC ZBOX Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX. Gently remove the cover as the image below. 12 ZOTAC ZBOX Installing a memory module 1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot at a 45 degree angle. Note: When installing two SO-DIMM memory modules, please insert a module into the lower slot first. 2. Gently press down on the memory module until it locks into place by the arms of the memory slot. Note: This ZOTAC ZBOX accomodates two DDR3 SO-DIMM memory modules. You must install at least one module in one of the two slots. 13 ZOTAC ZBOX Removing the memory module 1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory module outwards, as shown in the image below, to release the memory module. 2. Remove the memory module from the slot at a 45-degree angle. 14 ZOTAC ZBOX Installing a hard disk 1. Locate the 2. 5-inch SATA hard disk and the hard disk bracket. 2. To do so : 1. Locate the screw hole on the bottom of the ZOTAC ZBOX. 2. Align the stand screw to the PC screw hole and then secure the Stand to the PC with a coin. Do not place your ZOTAC ZBOX on the desktop without the stand.  Installing your ZOTAC ZBOX to a monitor You can also install your ZOTAC ZBOX to the back of a monitor. To do so: 1. Secure the VESA mount to your monitor with four screws (HNM/M4x8). 2. Place your ZOTAC ZBOX on the VESA mount noting the correct alignment and then secure the PC to the VESA mount with a coin. To fasten the VESA mount, your monitor must comply with VESA75 Or VESA100  standard.  Mechanical Loading Stability - Mounting of the equipment on the backside of the  monitor should be lay this equipment on a reliable surface when install. If the total weight of your monitor and ZOTAC ZBOX is over 7kg, the system may be unstable. 19 ZOTAC ZBOX IR receiver Enjoy more of your favorite entertainment by MCE (Media Center Edition) remote controller with USB IR receiver (connecting to USB 2. 0 port). External USB IR receiver Remote control ZOTAC ZBOX is shipped with a remote control. Follow the instructions below to use the remote control. Function keys Navigation Buttons OK START OK Playback Buttons i RECORD    BACK PAUSE   = STOP   INFORMATION  UP  DOWN  LEFT  RIGHT REW  PLAY FWD REPLAY SKIP Shortcut Buttons | GUIDE SLEEP WAKE Audio and Video Buttons +  + - 1 4 7 *. CLEAR Numeric Keypad 2 5 8 0 Teletext Buttons T BLUE 3 6 9 # ENTER -    VOLUME UP / DOWN MUTE CHANNEL UP / DOWN RED TELETEXT GREEN YELLOW Note: Some remote control functions listed above are only available with the relative hardware equipments. [. . . ] Select Connect to the Internet and click Next. 7. Select your connection type and click Next. 10. Click Finish to finish the configuration. Click Connect to connect to the internet. [. . . ]