User manual ZYXEL PRESTIGE 652HWI

[. . . ] Prestige 652 Series ADSL Security/Wireless LAN Router User's Guide Version 3. 40 June 2003 Prestige 652 Series User's Guide Copyright Copyright © 2003 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. [. . . ] Enter the geographic location (up to 31 characters) of your Prestige. Enter the name (up to 30 characters) of the person in charge of this Prestige. Enter the domain name (if you know it) here. If you leave this field blank, the ISP may assign a domain name via DHCP. You can go to menu 24. 8 and type "sys domainname" to see the current domain name used by your gateway. If you want to clear this field just press the [SPACE BAR]. The domain name entered by you is given priority over the ISP assigned domain name. Edit Dynamic DNS Route IP Bridge Press the [SPACE BAR] to select Yes or No (default). Select Yes to configure Menu 1. 1 -- Configure Dynamic DNS (discussed next). Set this field to Yes to enable or No to disable IP routing. You must enable IP routing for Internet access. Turn on/off bridging for protocols not supported (for example, SNA) or not turned on in the previous Route IP field. Select Yes to turn bridging on; select No to turn bridging off. No Yes No EXAMPLE P652HW Location (optional) Contact Person's Name (optional) Domain Name MyHouse JohnDoe zyxel. com. tw 23-2 Menu 1 General Setup Prestige 652 Series User's Guide 23. 2. 1 Procedure to Configure Dynamic DNS If you have a private WAN IP address, then you cannot use Dynamic DNS. To configure Dynamic DNS, go to Menu 1 -- General Setup and select Yes in the Edit Dynamic DNS field. Press [ENTER] to display Menu 1. 1-- Configure Dynamic DNS as shown next. Menu 1. 1 - Configure Dynamic DNS Service Provider = WWW. DynDNS. ORG Active= Yes Host= me. ddns. org EMAIL= mail@mailserver USER= username Password= ********* Enable Wildcard= No Press ENTER to confirm or ESC to cancel: Figure 23-2 Menu 1. 1 Configure Dynamic DNS Follow the instructions in the next table to configure Dynamic DNS parameters. Table 23-2 Menu 1. 1 Configure Dynamic DNS FIELD Service Provider Active Host EMAIL USER Password Enable Wildcard DESCRIPTION This is the name of your Dynamic DNS service provider. Press [SPACE BAR] to select Yes and then press [ENTER] to make dynamic DNS active. Enter the domain name assigned to your Prestige by your Dynamic DNS provider. Press [SPACE BAR] and then [ENTER] to select Yes or No This field is N/A when you choose DDNS client as your service provider. No EXAMPLE WWW. DynDNS. ORG (default) Yes me. dyndns. org mail@mailserver When you have completed this menu, press [ENTER] at the prompt "Press ENTER to Confirm. . . " to save your configuration, or press [ESC] at any time to cancel. Menu 1 General Setup 23-3 Prestige 652 Series User's Guide Chapter 24 Menu 2 WAN Backup Setup This chapter describes how to configure traffic redirect and dial-backup using menu 2, 2. 1, 2. 2 and 2. 2. 1. 24. 1 Introduction to WAN Backup Setup This chapter explains how to configure the Prestige for traffic redirect and dial backup connections. 24. 2 Dial Backup To set up the auxiliary port (DIAL BACKUP on the Prestige 652 or AUX on the Prestige 652H/HW) for use in the event that the regular WAN connection is dropped, first make sure you have set up the port connection (and the CON/AUX switch to AUX on the Prestige 652H/HW) and then configure: 1. Menu 2 - WAN Backup Setup Menu 2. 2 ­ Dial Backup Setup Menu 2. 2. 1 - Advanced Dial Backup Setup Menu 11. 1 - Remote Node Profile Refer also to the traffic redirect section for information on an alternate backup WAN connection. 24. 3 Configuring Dial Backup in Menu 2 From the main menu, enter 2 to open menu 2. Menu 2 WAN Backup Setup 24-1 Prestige 652 Series User's Guide Menu 2 - Wan Backup Setup Check Mechanism = DSL Link Check WAN IP Address1 = 0. 0. 0. 0 Check WAN IP Address2 = 0. 0. 0. 0 Check WAN IP Address3 = 0. 0. 0. 0 KeepAlive Fail Tolerance = 0 Recovery Interval(sec) = 0 ICMP Timeout(sec) = 0 Traffic Redirect = No Dial Backup = No Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 24-1 Menu 2 WAN Backup Setup The following table describes the fields in this menu. [. . . ] 28-2 Virtual Private Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 VPI & VCI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 W WAN Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2 WAN to LAN Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]