User manual ZYXEL VSG1432-B101 QUICK START GUIDE V1.10

[. . . ] · Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. [. . . ] LAN: Use an Ethernet cable to connect a computer to a LAN port for initial configuration and/or Internet access. USB: Connect a USB (version 2. 0 or lower) memory stick or a USB hard drive for file sharing. Use a USB extension cable if the stick is too big to fit. POWER: Use the provided power adaptor to connect the POWER socket to an appropriate power source. Make sure the power at the outlet is on. After connecting the power adaptor, look at the lights on the front panel. · The POWER light blinks while your VSG1432-B101 starts up and then stays on once it is ready. · Each LAN light stays on if the corresponding LAN port is properly connected and blinks when there is traffic. · The ETHERNET WAN light stays on if the ETHERNET WAN port is properly connected and blinks when there is traffic. · The USB light turns on when your VSG1432-B101 detects a connected USB device. · The DSL WAN light turns on when your VSG1432-B101 has a DSL connection. 7 · The WLAN / WPS light flashes green and orange while WPS is in process. It stays on green when the wireless LAN is ready and blinks when there is traffic. · The INTERNET light turns on when the gateway is able to access the Internet and will blink when your VSG1432-B101 is sending or receiving data. If the lights do not come on, check your connections and inspect your cables for damage. If the lights are still off, contact technical support. 8 VSG1432-B101 Series Set Up a Wireless Network You can set up a wireless network using the following methods: Using Wireless Protected Setup (WPS) Press the WPS button on the VSG1432-B101's front panel for more than 5 seconds to turn the WPS function on. Follow these steps to add a WPS-enabled device to the wireless network using the WPS/WLAN button. 1 one another. Place the devices you want to connect near 1 Press the WPS button on the VSG14322 B101. The WPS light blinks green and orange. 3 device within 2 minutes of pressing the button on the VSG1432-B101. The WPS light on the VSG1432-B101 shines steadily when connected. Press the WPS button on a compatible 9 Set Up a Wireless Network Manually The wireless LAN on your VSG1432-B101 is enabled by default. To add a wireless client to the network, use the settings found on the bottom panel of your VSG1432-B101, which will look similar to the following example: SSID: ZyXEL00561 Security Mode: WPA-PSK Pre-Shared Key: FB373BD356 Configure wireless devices that you want to connect to the wireless network to use the same wireless settings as the VSG1432-B101. The default wireless settings vary for each VSG1432-B101. Refer to the bottom panel of your device and use the provided information. Log into the Web Configurator Your device may already be set up for Internet access. However, you may want or need to log on to the VSG1432-B101 Web Configurator to perform tasks: · Configure your Internet access settings manually · Customize the Quality of Service (QoS) and routing features · Create firewall and web filter rules · Edit remote management, as well as other features 10 VSG1432-B101 Series 1. In your browser, if the VSG1432-B101 does not automatically redirect you to the login screen, go to http://192. 168. 1. 1. 2. [. . . ] For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]