User manual ZYXEL ZYWALL USG 50

[. . . ] ZyWALL USG 50 Unified Security Gateway Default Login Details LAN Port IP Address User Name Password P3, P4 https://192. 168. 1. 1 admin 1234 Version 2. 21 Edition 1, 5/2010 www. zyxel. com www. zyxel. com Copyright © 2010 ZyXEL Communications Corporation About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to want to configure the ZyWALL using the Web Configurator. How To Use This Guide · Read Chapter 1 on page 31 chapter for an overview of features available on the ZyWALL. · Read Chapter 3 on page 43 for web browser requirements and an introduction to the main components, icons and menus in the ZyWALL Web Configurator. · Read Chapter 4 on page 59 if you're using the installation wizard for first time setup and you want more detailed information than what the real time online help provides. · Read Chapter 5 on page 69 if you're using the quick setup wizards and you want more detailed information than what the real time online help provides. [. . . ] Set policies for other applications (except SIP) to lower priorities so the local users' HTTP traffic gets sent before non-SIP traffic. · Enable maximize bandwidth usage so the HTTP traffic can borrow unused bandwidth. Figure 275 HTTP Any to WAN Bandwidth Management Example Outbound: 200 kbps BWM BWM Inbound: 500 kbps ZyWALL USG 50 User's Guide 451 Chapter 29 Application Patrol 29. 1. 3. 5 FTP WAN to DMZ Bandwidth Management Example · ADSL supports more downstream than upstream so you allow remote users 300 kbps for uploads to the DMZ FTP server (outbound) but only 100 kbps for downloads (inbound). · Disable maximize bandwidth usage since you do not want to give FTP more bandwidth. Figure 276 FTP WAN to DMZ Bandwidth Management Example Outbound: 300 kbps BWM BWM Inbound: 100 kbps 29. 1. 3. 6 FTP LAN to DMZ Bandwidth Management Example · The LAN and DMZ zone interfaces are connected to Ethernet networks (not an ADSL device) so you limit both outbound and inbound traffic to 50 Mbps. · Disable maximize bandwidth usage since you do not want to give FTP more bandwidth. Figure 277 FTP LAN to DMZ Bandwidth Management Example BWM Inbound: 50 Mbps BWM Outbound: 50 Mbps 452 ZyWALL USG 50 User's Guide Chapter 29 Application Patrol 29. 2 Application Patrol General Screen Use this screen to enable and disable application patrol. It also lists the registration status and details about the signature set the ZyWALL is using. Note: You must register for the IDP/AppPatrol signature service (at least the trial) before you can use it. See Section 10. 1 on page 209 for how to register. Click Configuration > App Patrol to open the following screen. Figure 278 Configuration > App Patrol > General The following table describes the labels in this screen. See Section 29. 3. 1 on page 455 for more information as well. Table 132 Configuration > App Patrol > General LABEL Enable Application Patrol Enable BWM DESCRIPTION Select this check box to turn on application patrol. This is a global setting for enabling or disabling bandwidth management on the ZyWALL. You must enable this setting to have individual policy routes or application patrol policies apply bandwidth management. This same setting also appears in the Network > Routing > Policy Route screen. Enabling or disabling it in one screen also enables or disables it in the other screen. ZyWALL USG 50 User's Guide 453 Chapter 29 Application Patrol Table 132 Configuration > App Patrol > General (continued) LABEL Enable Highest Bandwidth Priority for SIP Traffic DESCRIPTION Select this to maximize the throughput of SIP traffic to improve SIPbased VoIP call sound quality. This has the ZyWALL immediately send SIP traffic upon identifying it. When this option is enabled the ZyWALL ignores any other application patrol rules for SIP traffic (so there is no bandwidth control for SIP traffic) and does not record SIP traffic bandwidth usage statistics. The following fields display information about the current state of your subscription for IDP/application patrol signatures. Registration Registration This field displays whether a service is activated (Licensed) or not (Not Status Licensed) or expired (Expired). Registration This field displays whether you applied for a trial application (Trial) or Type registered a service with your iCard's PIN number (Standard). None displays when the service is not activated. Apply new This link appears if you have not registered for the service or only have Registration the trial registration. Click this link to go to the screen where you can register for the service. Signature Information Current Version Released Date Update Signatures Apply Reset The following fields display information on the current signature set that the ZyWALL is using. This field displays the IDP signature and anomaly rule set version number. This number gets larger as the set is enhanced. This field displays the date and time the set was released. Click this link to go to the screen you can use to download signatures from the update server. [. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 4 FCC Radiation Exposure Statement · This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 930 ZyWALL USG 50 User's Guide Appendix F Legal Information Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Viewing Certifications 1 2 3 Go to http://www. zyxel. com. [. . . ]