User manual 3COM S9512 FABRIC II

[. . . ] H3C S9500 Series Routing Switches Installation Manual Hangzhou H3C Technologies Co. , Ltd. http://www. h3c. com Manual Version: T2-08048H-20071025-C-2. 03 Product Version: S9500-CMW520-R2127 Copyright © 2006-2007, Hangzhou H3C Technologies Co. , Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co. , Ltd. Trademarks H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co. , Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners. Notice The information in this document is subject to change without notice. [. . . ] When passing through a metallic board hole or bending along the acute side of mechanical parts, the fiber must wear jackets or cushions. Never exert a fierce force to the fiber or plug; otherwise the plug may be damaged or the fiber may be broken. Never pull, press or extrude the fiber fiercely. For the allowed maximum tensile load and crush load, refer to Table 3-4. Table 3-4 Allowed maximum tensile force and crush load Period of force Short period Long term Tensile load (N) 150 80 Crush load (N/100 mm) 500 100 IV. Connection procedure 1) 2) Connect one end of the fiber to the SFP module of the S9500 series. Connect the other end of the fiber to the peer device. 3-26 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch 3. 10 Verifying the Installation Warning: Make sure that you have turned off the power before checking the installation in case of bodily injury and device damage. After installing the switch, verify the installation against the following list. For the successful installation, all items must be normal. Table 3-5 Installation checklist Item Console cable PGND wire Power cables SRPUs LPUs/service boards Fan tray(s) PSUs Normal Abnormal (Description) 3-27 Installation Manual H3C S9500 Series Routing Switches Table of Contents Table of Contents Chapter 4 Commissioning the Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4. 1 Setting Up Configuration Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4. 1. 1 Setting Up Configuration Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4. 1. 2 Setting Terminal Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4. 2 Powering On the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 4. 2. 1 Checklist for Switch Power-On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 4. 2. 2 Powering on the Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 4. 2. 3 Verifying after Power-on (Recommended). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 4. 2. 4 Boot Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 i Installation Manual H3C S9500 Series Routing Switches Chapter 4 Commissioning the Switch Chapter 4 Commissioning the Switch 4. 1 Setting Up Configuration Environment 4. 1. 1 Setting Up Configuration Environment Connect a terminal (a PC in this example) to the switch with the console cable. Figure 4-1 Connect a PC to the switch with a Console cable 4. 1. 2 Setting Terminal Parameters This section describes how to set the terminal parameters. 1) 2) Start the PC, and run the terminal emulation program. The following uses a PC running Windows XP HyperTerminal as an example. Select Start > Programs > Accessories > Communications > HyperTerminal in the window to set up a new to access the HyperTerminal window. The Connection Description dialog box appears, as shown in Figure 4-2. [. . . ] The labels for AC power cables are affixed to one side of the identification plates on cable ties. I. Meaning of the label Table B-6 shows the information carried on the labels for the AC power cables. Table B-6 Information on labels affixed to the AC power cables Content Meaning MN: serial number of the cabinet or the socket where the power is led in MN-AC The location of the socket is marked out according to onsite situation. If the sockets can be identified by row number and column number, they can be numbered following the same rule for the cabinets. [. . . ]