User manual 3M 02-2004 DEBURRING AND FINISHING HINGES AND DOOR HANDLES

[. . . ] Application Profile Market: Builders Hardware Application Description: Deburring and Finishing Hinges and Door Handles Pre-polishing door handle (grade 400) Finishing hinge (grade 120) Key Application Requirements Prepare contoured builder's hardware parts for pre-plating or polishing, including deburring and finishing steps. The most common metals used include brass, cold rolled steel and stainless steel. [. . . ] Doesn't cause distortion to the part. 3M Industrial Business Market: Builders Hardware Application Description: Deburring and Finishing Hinges and Door Handles page 2 Advantages of Scotch-BriteTM Radial Bristle Brush over Competition Conformability Scotch-Brite Radial Bristle Brush Wire Brush Life Consistency Safety/Cleanliness Easy to use, does not throw wires or fiber Performance Good finish; CubitronTM Abrasive Grain for cut performance. Comes in a wide range of grades. Very conformable; Long lasting quality Uniform cut that less manipulation throughout life of permits consistency for operator of part product Little conformability, lots of pressure necessary Long lasting but loses shape quickly Short Life Finish varies from part to part Consistent finish Throws high velocity, Many times does not needle-like wires remove targeted at the operator material Used fiber debris may Good finish, low cut plug dust collectors, performance, short life hard to clean up Used fiber debris may Good finish and cut plug dust collectors, performance, short hard to clean up life Non-Woven Very conformable Abrasive Disc Nylon Brush Moderately conformable Short, effective life Not consistent, performance drops off after a few minutes Application Suggested Grades Deburring, cleaning Finishing, pre-polishing TS 50, 80 or 120 TC 220 or 400 Recommended RPM 1, 750 ­ 3, 600 1, 750 ­ 3, 600 Accessories Flange Adaptor Flange Adaptor No. 4 UPC 048011-09303-1 048011-09158-7 048011-09157-0 048011-09134-8 048011-09156-3 3M Brush Extender Spacer 3M Brush Flange (side) 3M Tapered Spindle Adapter 048011-33092-1 048011-33093-8 PN02808 Function Reduce 1. 25" ID to fit 1/2" Reduce 1. 25" ID to fit 5/8" Reduce 1. 25" ID to fit 3/4" Reduce 1. 25" ID to fit 7/8" Reduce 1. 25" ID to fit 1" Market: Builders Hardware Application Description: Deburring and Finishing Hinges and Door Handles page 3 Tech Tips ­ Do not use excessive downward pressure on the tool -- let the tool and bristle tips do the work. ­ Bristle discs perform the best when slightly angled (2-4 degrees). ­ Do not work bristle over sharp edges, when finishing edges on flat surface; position the tool so that the bristles run off the edge and not into the edge. ­ Do not dwell on a localized area to avoid excessive heat build up. ­ When using the type T-C bristle products, the bristles are directional. Additional Information Scotch-Brite Radial Bristle Brush, 8-inch: product flyer (61-5002-8041-9) Scotch-Brite Bristle Discs and Brushes: product family brochure (61-5002-8009-6) Safety Information Always read and follow all safety information included with the product. Do not exceed maximum operating RPM's. Follow safety operation procedures posted in work areas. To request additional product information or to arrange for sales assistance, call 1-800-362-3550. Address correspondence to: 3M Industrial Business Customer Response Center, Building 21-1W-10, 900 Bush Avenue, St. All statements, technical information and recommendations contained in this document are based upon tests or experience that 3M believes are reliable. [. . . ] Except where prohibited by law, 3M and seller will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental, or consequential, regardless of the legal theory asserted, including warranty, contract, negligence, or strict liability. For Additional Information Product Use Warranty and Limited Remedy Limitation of Liability 3M, Scotch-Brite and Cubitron are trademarks of 3M. Industrial Business Building 21-1W-10, 900 Bush Avenue St. Paul, MN 55106 BHdfhingesb. pdf © 3M 2004 IBD4106 [. . . ]