User manual 3M 718 STATIC SENSOR PRODUCT BULLETIN

[. . . ] 3 718 Static Sensor 718A Air Ionizer Test Kit two functions; when pressed momentarily it switches between the two measurement ranges of 0-2, 000 volts and 0-20, 000 volts, and if held for longer than 3 seconds, it resets the voltage display to 0 volts. The HOLD button allows the user to freeze a measurement on the LCD for later review. Ranging System Included with the 718 Static Sensor is a ranging system consisting of two light-emitting diodes (LEDs) which each emit a circular red light onto the surface being measured for static. [. . . ] Meter Functions The meter is equipped with three membrane switches which control different functions. The POWER switch turns the instrument on and off. The RANGE/ZERO button performs Measurement Accuracy Certifications Voltage Display Voltage Output 718 Range Finder Unfocused 718 Range Finder at 1" away Accuracy The 718 Static Sensor is accurate to within ±5% of the displayed measurement, at a distance of one inch (2. 54 cm) from the target. Accuracy will vary as the distance between measured object and instrument changes from the one inch (2. 54 cm) specification. Analog Output Jack The analog output jack located in the front of the unit provides a convenient hook-up, via a 3/32 inch (2. 5 mm) monophone jack, to a recorder/data acquisition console. The 718 Static Sensor may then be used for remote monitoring or permanent recording of electrostatic voltage readings. 3M 718 Static Sensor Specifications Dimensions Weight Power Requirements Measurement Ranges 0. 85" (H) x 2. 4" (W) x 4. 15" (L) 2. 2 cm (H) x 6. 1 cm (W) x 10. 5 cm (L) 4. 5 oz. (128 g) with battery One 9-volt alkaline battery 0 ­ 2 kV Low Range 0 - 20 kV High Range 3 1 2 digit liquid crystal display 1/1000 of measured voltage @ low range 1/10, 000 of measured voltage @ high range LED targets. (2. 54 cm) measurement distance Within 5% of actual voltage UL, C-UL, CE, CB-scheme, NOM Distance Indicator for measurement of the ionizer's offset balance. The charger can be used to deposit an electrostatic charge on the plate. Measuring how long it takes the ionizer to neutralize this static charge gives the ionizer discharge time. Calibration and Certification The 3M 718 Static Sensor can be ordered as calibrated and certified by a 3M ISO9002 Registered Metrology Laboratory. Calibration can be traced back to National Institute of Standards and Technology (NIST) standards, as specified in MIL-STD-45662. 3M 718A Air Ionizer Test Kit Specifications Charge Plate Assembly Per ESD Association Draft Standard D3. 3 1" (H) x 3. 1" (W) x 4. 25" (L) 2. 5 cm (H) x 7. 9 cm (W) x 10. 8 cm (L) 3. 25" (W) x 1. 25" (L) 8. 3 cm (W) x 3. 2 cm (L) 2. 5 oz (70 g) 0. 85" (H) x 2. 4" (W) x 5. 0" (L) 2. 2 cm (H) x 6. 1 cm (W) x 12. 7 cm (L) 6 oz. (170 g) with battery 3M 718A Air Ionizer Test Kit Charge Plate Bracket Dimensions Charge Plate Area 3MTM 718A Air Ionizer Test Kit When used with the 3MTM 718 Static Sensor, the 3MTM 718A Air Ionizer Test Kit can provide periodic verification of air ionizer performance. The 718A Air Ionizer Test Kit consists of a charge plate and a charger. [. . . ] If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted. 3 Electronic Handling & Protection Division 6801 River Place Blvd. Austin, TX 78726-9000 http://www. 3M. com/ehpd Recycled paper 40% Pre-consumer waste paper 10% Post-consumer waste paper Litho in USA. [. . . ]