User manual 3M ACCENTRIM PRODUCTS MANUFACTRING BROCHURE

[. . . ] Accentrim Products TM Surface Enhancing Technology 2 1 Enhancing the view from the inside and out 3 Add extra to ordinary with the distinction and brilliance of Optically Divided Lites 4 Create the beauty of Optically Divided Lite with 3MTM AccentrimTM Products. This innovative surface-enhancing technology brings the beauty of Optically Enhanced Glass to windows, doors, transoms, side lites, etc. [. . . ] · · GED Integrated Application System · · Applies products at a rate of 15" per second Totally automated ­ requires no operator intervention or trim piece removal Allows production cycle time of less than one minute for an average-size unit Eliminates edge damage with electronic edge squaring Downloads production schedules automatically with integrated GED WinSystem1TM Software · · · · With 3M patented technology and advanced application systems from Glass Equipment Development (GED), GED is a specialist in window and door industry equipment and the following are options to meet your production requirements: For position only 9 Integrated Application System Application Table 11 GED Application Table · Applies products at a rate of 7" per second · Offers unlimited decorative possibilities · Includes easy-to-use design software to create and store consistently repeatable custom patterns · Imports decorative patterns from common CAD software Get the facts on 3MTMAccentrimTM Products and GED application equipment. For information on 3MTM AccentrimTM Products, call 1-800-362-3550 or visit www. 3m. com/accentrim 10 For information on GED application equipment, call 1-330-963-5401 or visit www. gedusa. com Specifications GED Integrated Application System Cycle time: Minimum glass size: Maximum glass size: Roll length: <1 minute per unit (24" x 36" 2 vertical x 1 horizontal lite) 12" x 12" 60" x 96" and up to 5/16" thick 120-yard roll of 3MTM AccentrimTM Product GED Application Table Cycle time: Minimum glass size: Maximum glass size: Roll length: 3 minutes per unit (24" x 36" 2 vertical x 1 horizontal lite with square-cut ends) 8" x 8" 60" x 96" and up to 1/4" thick 60 or 120 yard roll of 3MTM AccentrimTM Product Technical Data Product Description A linered optical film with a very clear, low out-gassing adhesive. This product employs proprietary technology and has excellent adhesion to glass surfaces, especially float glass. This permanent adhesive resists edge lifting and discoloration, and has excellent long-term aging properties. A-100 A-200 A-300 A-400 Pattern Edge Bevel V-Groove Fluted V-Groove Half-Round with Center Transition Typical Physical Properties & Performance Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Adhesion (ASTM D-3330) Initial After 3 days at 72°F (22°C) Float Glass (oz. /0. 5in. [N/50mm]) 40 (44) 60 (65) Construction Description Optical Layer Backing Adhesive Release Liner Material Acrylic Polyester High strength acrylic Polyester with release agent General Information · Not intended for outdoor application. · Application temperature should be normal room temperature, 60° to 80°F (16° to 27°C). · Dimensionally stable over temperature range from -20°F to 225°F (-29°C to 107°C). · Reference 3M. com/accentrim for warranty information regarding insulating glass. TECHNICAL INFORMATION AND DATA: The technical information and data, recommendations, and other statements provided are based on tests or experience which 3M believes to be reliable, but the accuracy or completeness of such information is not guaranteed. PRODUCT USE: Please remember that many factors can affect the use and performance of a 3M product in a particular application. The materials to be adhered with the 3M product, the surface preparation of those materials, the product selected for use, the conditions in which the product is used, and the time and environmental conditions in which the product is expected to perform are among the many factors that can affect the use and performance of a 3M product. Given the variety of factors that can affect the use and performance of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user's method of application. [. . . ] In no event shall 3M be liable for the labor or installation costs of replacing the 3M product. Industrial Business Industrial Adhesives and Tapes Division Building 21-1W-10 900 Bush Avenue St. Paul, MN 55144 1-800-362-3550 www. 3M. com/accentrim ©2004, 3M. [. . . ]