User manual 3M RESPIRATORS FOR ABATEMENT AND MOLD REMEDIATION

[. . . ] 3MTM Respirators for Abatement 1 and Mold Remediation Committed to your health and safety 2 3Innovation 3M TM Abatement Respirators Comfort and durability--the right combination for abatement New 3MTM Half Facepiece Respirator 7500 Series Ultimate Reusable New 3MTM Filter 7093, P100 · Improved filter technology provides up to 25% improvement in breathing resistance. · Innovative solid-top air-inlet design: - No tape required during showering or decontamination. - Protects and increases the service life of the filter. [. . . ] · Reduces exposure to mold spores. NEW! 3MTM Cartridges/Filters 60923 and 60926* · Use with 3M half and full facepiece respirators for cleaning compounds that contain chlorine, chlorine-dioxide or certain organic vapors. 14 15 16 For more information on mold remediation, go to www. 3M. com/occsafety/mold Maximum comfort for the professional mold remediator 3MTM Powered Air Purifying Respirator (PAPR) Kit · Provides high level of airflow to increase worker comfort and productivity. · Equipped with rechargeable eighthour battery. · Kit includes a bump cap, breathing tube, comfort belt-mounted PAPR assembly, organic vapor/HEPA cartridge and shower cover. 18 3MTM Cartridge GVP-443* · Use with 3MTM GVP PAPR for cleaning compounds that contain chlorine, chlorine dioxide or certain organic vapors. 19 17 Ordering Information Part Number 6700 6800 6900 67097 68097 69097 GVP-PSK Description Full Facepiece, Small Full Facepiece, Medium Full Facepiece, Large Mold Remediation Respirator Kit, Small Mold Remediation Respirator Kit, Medium Mold Remediation Respirator Kit, Large Powered Air Purifying Respirator Kit Part Number Description 2097 20 GVP-441 GVP-443 Particulate Filter P100 With Nuisance-Level Organic Vapor Relief** Cartridge, Organic Vapor/HEPA Cartridge, Organic Vapor/Acid Gas/HEPA 21 NEW!NEW! 22 16 17 18 60923 60926 Cartridge/Filter, Organic Vapor/Acid Gas/P100 14 Cartridge/Filter, Multi-Gas/Vapor/P100 23 *Gases and vapors associated with disinfectants (e. g. , chlorine and ammonia) should be measured, and may warrant the use of an appropriate chemical cartridge in conjunction with the particulate filter. Please see disinfectant MSDS for further information. **Nuisance level refers to concentrations below current OSHA PELs. Other Related 3M Products NE W! 24 25 3MTM Duct Tape 3900 · Strong adhesion (21 lbs. /in. width tensile strength) with low-tack edges. · Tears easily from roll. 3MTM HEPA Vacuum · Designed for fast, easy cleanup of hazardous material. · Extremely lightweight and self-contained for easy storage and transport. 3MTM Super 77 Multi-Purpose Spray Adhesive · Quickly and easily bonds poly. · Dries quickly and resists moisture. 26 Q&A Q A During abatement work, I wear a half facepiece respirator. Can I use it for mold remediation too? W!NE Medical Clearance Q A Can I use the same filters for mold remediation that I use for asbestos abatement? Not by itself. Because mold can be irritating to the eyes, the EPA allows the use of half facepiece respirators for remediation of contaminated areas up to 100 square feet only when used with non-vented goggles. Since full facepiece respirators may be used for mold remediation jobs of all sizes, they are a simple solution for both respiratory and eye protection. No. The P100 or HEPA filters commonly used for asbestos abatement do not reduce exposure to the VOCs that are produced by mold. In order to reduce exposure to both mold spores and VOCs, 3M recommends a particulate filter with either nuisance-level organic vapor relief or an organic vapor cartridge. Easy-to-use materials clear employees for respirator use and help you comply with OSHA regulations. · Two low-cost, convenient ways to administer the questionnaire: - Mail-in clearance call 1-877-844-8378 - On-line clearance call 1-800-383-3393 For more information In the United States, contact: Technical Assistance 1-800-243-4630 Sales Assistance 1-800-896-4223 Fax-on-Demand 1-800-646-1655 Internet www. 3M. com/occsafety E-mail occsafety@mmm. com For other 3M products: 1-800-3M-HELPS or 1-651-737-6501 In Canada, contact: Technical Assistance 1-800-267-4414 Marketing 3M Canada Company, OH&ES 1-800-265-1840, ext. [. . . ] All respirator instructions, warnings and use and time limitations must also be read and understood by the wearer before use. Before use of these respirators, a written respiratory protection program must be implemented, meeting all the requirements of OSHA 29 CFR 1910. 134, including training and fit testing. 3 General Offices 3M Center St. Paul, MN 55144-1000 Minimum 10% Post-Consumer Fiber 3M, the 3M logo, Cool Flow and Powerflow are trademarks of 3M. [. . . ]