User manual ABIT AS8-G

[. . . ] (AS8, AS8-V, AS8-G) Intel Pentium 4 System Board Socket 775 User's Manual AS8 Series 4200-0409-05 Rev. 1. 02 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] [Combined Mode]: Parallel ATA and Serial ATA are combined together. [Enhanced Mode]: Enable both Parallel ATA and Serial ATA. [SATA Only]: The SATA is operating in legacy mode. Serial ATA 1 Mode / Serial ATA 2 Mode: This item determines the function mode for Serial ATA Port 1 (i. e. The SATA1 connector in this model) and Serial ATA Port 2 (i. e. Both SATA1 and SATA2 will be served each as one single IDE connector after selected as the following modes: Mode Serial ATA Port 1 (SATA1) Serial ATA Port 2 Description (SATA2) · SATA1 serves as IDE-3 Master · SATA2 serves as IDE-4 Master · OnChip IDE-1 and IDE-2 controller enabled · SATA1 serves as IDE-4 Master · SATA2 serves as IDE-3 Master · OnChip IDE-1 and IDE-2 controller enabled · SATA1 serves as IDE-1 Master · SATA2 serves as IDE-1 Slave · OnChip IDE-1 controller disabled · SATA1 serves as IDE-1 Slave · SATA2 serves as IDE-1 Master · OnChip IDE-1 controller disabled · SATA1 serves as IDE-2 Master · SATA2 serves as IDE-2 Slave · OnChip IDE-2 controller disabled · SATA1 serves as IDE-2 Slave · SATA2 serves as IDE-2 Master · OnChip IDE-2 controller disabled IDE-3 Master Enhanced IDE-4 Master IDE-4 Master IDE-3 Master IDE-1 Master IDE-1 Slave IDE-1 Slave Combined IDE-2 Master IDE-1 Master IDE-2 Slave IDE-2 Slave IDE-2 Master AS8 Series BIOS Setup 3-19 IDE-1 Master SATA Only IDE-2 Master IDE-2 Master · SATA1 serves as IDE-1 Master · SATA2 serves as IDE-2 Master · OnChip IDE-1 and IDE-2 controller disabled · SATA1 serves as IDE-2 Master · SATA2 serves as IDE-1 Master · OnChip IDE-1 and IDE-2 controller disabled IDE-1 Master OnChip PCI Device: Click <Enter> key to enter its submenu: OnChip USB Controller: This option enables or disables the USB controller. USB 2. 0 Controller: This option enables or disables the USB 2. 0 controller. USB Keyboard Support Via: This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS environment. USB Mouse Support Via: This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. OnChip Audio Controller: This option enables or disables the audio controller. User's Manual 3-20 Chapter 3 SuperIO Device: Click <Enter> key to enter its submenu: Onboard FDC Controller: This option enables or disables the onboard FDC controller. Onboard Serial Port: This item determines which I/O addresses the onboard Serial Port controller will access. [Auto]: The system automatically select an I/O address for the onboard Serial Port. [3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]: Allows you to manually select an I/O address for the onboard Serial Port. [Disabled]: Disables the onboard Serial Port. Onboard Parallel Port: This item specifies the I/O address used by the parallel port. [Disabled]: This option prevents the parallel port from accessing any system resources. When the value of this option is set to [Disabled], the printer port becomes unavailable. [378/IRQ7]: This option allows the parallel port to use [378/IRQ7] as its I/O port address. The majority of parallel ports on computer systems use IRQ7 and I/O Port 378H as the standard setting. [278/IRQ5]: This option allows the parallel port to use [278/IRQ5] as its I/O port address. [3BC/IRQ7]: This option allows the parallel port to use [3BC/IRQ7] as its I/O port address. Parallel Port Mode: This item specifies the parallel port mode. [. . . ] They will be more familiar with local conditions and problems and will have better insight as to which resellers offer what products and services. Due to the huge number of emails coming in every day and other reasons, such as the time required for problem reproduction, we will not be able to reply to every email. Please understand that we are selling through distribution channels and don't have the resources to serve every end-user. However, we will try to do our best to help every customer. [. . . ]