User manual ABIT BX6

[. . . ] The information in this document is subject to change without notice and does not represent a commitment on part of the vendor , who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special , incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are property of their respective owners. [. . . ] After you have configured the Power Management feature, press "Esc" to go back to the Main Menu. We are now going to briefly explain the options in this menu: Power Management: Four options: ä ä User Define User Define defines the delay for accessing the power modes. Min Saving When the three saving modes are enabled, the system is set up for minimum power savings. Doze = 1 hour Standby = 1 hour Suspend = 1 hour Max Saving When the three saving modes are enabled, the system is set up for maximum power savings. Doze = 1 minute Standby = 1 minute Suspend = 1 minute ä PM Control by APM: Power Management is completely controlled by the APM. APM stands for Advanced Power Management, it is a power management standard set by Microsoft, Intel and other major manufacturers. Video Off Method: Three video off methods are available: "Blank", "V/H SYNC + Blank" and "DPMS". The default is "V/H SYNC + Blank". If this setting does not shut off the screen, select "Blank". If your monitor and video card support DMPS standard, select "DPMS". Introduction of BIOS 3-19 Video Off After: Select the saving mode in which the video is switched off. ä ä ä ä NA The video will never be switched off in no power saving mode. Doze The video will be switched off in all power saving modes. Standby The video will only be switched off in Standby or Suspend mode. Suspend The video will only be switched off in Suspend mode. IDE HDD Power Down: If the system has not accessed data on the hard disk drive during the specified time period, the engine of the HDD will stop in order to save electricity. You can set 1 to 15 minutes or select Disable according to your use of the HDD. Doze Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning that computer is inactive during this period, the system will enter the Doze power saving mode. If this mode is disabled, the system will enter the next mode in the sequence (Standby or Suspend mode). Standby Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning the computer is inactive during this period, the system will enter the Standby power saving mode. If this mode is disabled, the system will enter the next mode in the sequence (Suspend mode). 3-20 Chapter 3 Suspend Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning the computer is inactive during this period, the system will enter the Suspend power saving mode. If this mode is disabled, the system will not enter the Suspend mode. Throttle Duty Cycle: This is used to specify the CPU speed in power saving mode. Seven options are available: 12. 5%, 25. 0%, 37. 5%, 50. 0%, 62. 5% or 75. 0% . CPU Fan Off In Option: CPU fan can be turned off in suspend mode. Power Button Override: Support ACPI Power Button Over-ride. The user presses the power button for more then four seconds while the system is in the working state, then the system will transition to the soft-off(Power off by software). [. . . ] This problem may be due to the Sound Card Driver. procedure, press SHIFT (BY-PASS) key, to skip CONFIG. SYS and AUTOEXEC. BAT; edit CONFIG. SYS with a text editor, and in front on the line that loads the Sound Card Driver, add a remark REM, in order to disable the Sound Card Driver. CONFIG. SYS: DEVICE=C:\DOS\HIMEM. SYS DEVICE=C:\DOS\EMM386. EXE HIGHSCAN DOS=HIGH, UMB FILES=40 BUFFERS=36 REM DEVICEHIGH=C:\PLUGPLAY\DWCFGMG. SYS LASTDRIVE=Z Restart the system. If the system starts and does not reset, you can be sure that the problem is due to the Sound Card Driver. [. . . ]