User manual ABIT BX6R2

[. . . ] Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special , incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are property of their respective owners. [. . . ] This is called the power button over-ride. Resume by LAN : To enable this feature, you must make sure your network software and network adapter (LAN card) support such a function. This function is also called " Wake on LAN " (WOL). Power on by Ring: If you connect an external modem to the onboard serial port, the system will be turned on when a telephone ring-up occurs. Power on by Alarm: RTC alarm can turn on the system. You can set date (of month) and time ( hour , minute , second ) . PM Timer Events: When one of the specifics occurs, the count down made for entry in power saving mode goes back to zero. Since the computer will enter a power saving mode only after an inactivity delay specified (time specific for Doze, Standby and Suspend modes) and after it has no activity, during this time period, any event will cause the computer to re-count the time elapsed. Resume events are operations or signals that cause the computer to resume time counting. äIRQ [3-7, 9-15], NMI: If any IRQ or NMI (Non-Mask Interrupt) activities occur, this will cause the computer to re-count the time elapsed. äVGA Active Monitor: If there is any VGA data transfer or any I/O activities, this will cause the computer to re-count the time elapsed. äIRQ8 Break Suspend : Supports the RTC alarm wake up from suspend function (via IRQ8). Introduction of BIOS 3-27 äIDE Primary Master: If any IDE primary master I/O activity occurs, it will cause the computer to re-count the time elapsed. äIDE Primary Slave: If any IDE primary slave I/O activity occurs, it will cause the computer to re-count the time elapsed. äIDE Secondary Master: If any IDE secondary master I/O activity occurs, it will cause the computer to re-count the time elapsed. äIDE Secondary Slave: If any IDE secondary slave I/O activity occurs, it will cause the computer to re-count the time elapsed. äFloppy Disk: If any floppy disk I/O activity occurs, it will cause the computer to re-count the time elapsed. äSerial Port: If any serial port I/O activity occurs, it will cause the computer to re-count the time elapsed. äParallel Port: If any IDE secondary master I/O activity occurs, it will cause the computer to re-count the time elapsed. äMouse Break Suspend: Four options are available: YesèNo (COM1) èNo (COM2) èNo (PS/2) èBack to Yes. 3-28 Chapter 3 (6) PnP/PCI Configuration In this menu, you can change the INT# and IRQ of the PCI bus and other hardware settings. Figure 3-7. PNP/PCI Configuration Menu PnP OS Installed: Device resource assigned by PnP OS or BIOS. Force Update ESCD: If you want to clear ESCD data next time you boot up, and ask the BIOS to reset the settings for the Plug & Play ISA Card and the PCI Card, select Enabled. But the next time you boot up, this option will automatically be set as Disabled. B Computer Knowledge B & ESCD (Extended System Configuration Data) The ESCD contains the IRQ, DMA, I/O Port, Memory information of the system. [. . . ] CONFIG. SYS: DEVICE=C:\DOS\HIMEM. SYS DEVICE=C:\DOS\EMM386. EXE HIGHSCAN DOS=HIGH, UMB FILES=40 BUFFERS=36 REM DEVICEHIGH=C:\PLUGPLAY\DWCFGMG. SYS LASTDRIVE=Z Restart the system. If the system starts and does not reset, you can be sure that the problem is due to the Sound Card Driver. Note down the Sound Card model, motherboard model, BIOS identification number on the technical support file (refer to main instructions), and describe the problem in the space provided. JJJ Technical Support H-3 Main instructions. . . To fill in this "Technical Support Form", refer to the step-by-step instructions given below: 1*. MODEL: Note the model number given in your user's manual. [. . . ]