User manual ABIT I-45CV

[. . . ] I-45C I-45CV Motherboard Intel Socket 775 Installation Guide Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both the FDD port and the floppy connector. To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the other end to the SATA device. Attach the SATA power cable to the SATA device and connect the other end from the power supply. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. The motherboard in this photo is served for DEMO only, and may not be the same type or model as the one described in this manual. I-45C/I-45CV 9 1. 7. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. 1. 7. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 10 I-45C/I-45CV 1. 7. 5 Front Panel Audio Connection Header This header provides the front panel connection for HD (High Definition) Audio, yet for AC'97 Audio CODEC connection, you must carefully check the pin assignment before connecting from the front panel module. An incorrect connection may cause malfunction or even damage the motherboard. Please do not connect the "Ground" cable or "USB VCC" cable from the front panel module to the Pin 4 "AVCC" of this header. Driver Configuration for AC'97 audio connection: The audio driver is originally configured to support HD Audio. For AC'97 audio connection, you may: 1. Right-click the "Realtek HD Audio Manager" icon in system tray. 2. Click "Audio I/O" tab, and then click "Connector Settings". Pin Assignment (HD AUDIO) MIC2 L AGND MIC2 R AVCC FRO-R MIC2_JD F_IO_SEN FRO-L LINE2_JD Pin Assignment (AC'97 AUDIO) MIC In GND MIC Power NC Line Out (R) NC NC Line Out (L) NC 11 3. Click "Disabled front panel jack detection", and then click "OK" to confirm. Pin 1 2 3 4 5 6 7 9 10 Pin 1 2 3 4 5 6 7 9 10 I-45C/I-45CV 1. 8 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEXP1". Install PCI Express X1 cards into slot "PCIE1". Install PCI cards into slots "PCI1" and/or "PCI2". 1. 9 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: · · · · · · Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. AUDIO1: Line-In: Connects to the line out from external audio sources. Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. LAN1: Connects to Local Area Network. · · 12 I-45C/I-45CV 2. [. . . ] Power supply wattage: Type in the power wattage of your power supply unit. Storage devices: Type in the brand and specifications of your HDD drive and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports, including the RAID allocation status. Example 1: WD Caviar WD600 60GB (on IDE2 master), Maxtor DiamondMax 10 SATA 300GB (on SATA 3) Example 2: Maxtor DiamondMax 10 SATA 300GB *2 (on SATA 3, SATA 4 RAID 1) Optical devices: Type in the brand and specifications of your optical drives and quantity. [. . . ]