User manual ABIT KV-85

[. . . ] KV-85 AMD Athlon 64 System Board Socket 754 User's Manual Rev. 1. 01 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] The BIOS will boot the operating system according to the sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another device other than these three items. Swap Floppy Drive: When set to [Enabled], and the system is booting from the floppy drive, the system will boot from drive B instead of the regular drive A. There must be two floppy drives connected in the system to use this function. KV-85 BIOS Setup 3-7 Boot Up Floppy Seek: When set to [Enabled], the BIOS will check whether the floppy disk drive is installed or not. Boot Up NumLock Status: This item determines the default state of the numeric keypad at system booting up. [On]: The numeric keypad functions as number keys. [Off]: The numeric keypad functions as arrow keys. Security Option: This item determines when the system will prompt for password - every time the system boots or only when enters the BIOS setup. [Setup]: The password is required only when accessing the BIOS Setup. [System]: The password is required each time the computer boots up. If you forget the password, you will have to open the computer case and clear all information in the CMOS before you can start up the system. But by doing this, you will have to reset all previously set options. Small Logo(EPA) Show: Enables or disables the display of the EPA logo during boot. User's Manual 3-8 Chapter 3 3-3. Advanced Chipset Features Phoenix ­ Award WorkstationBIOS CMOS Setup Utility Advanced Chipset Features AGP & P2P Bridge Control Press Enter Item Help DRAM Clock/Drive Control Press Enter LDT & PCI Bus Control Press Enter Vlink Data Rate 8X Init Display First PCI Slot :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults # AGP & P2P Bridge Control: Click <Enter> key to enter its submenu: Phoenix ­ Award WorkstationBIOS CMOS Setup Utility Advanced Chipset Features AGP Aperture Size 128M Item Help AGP 2. 0 Mode 4X AGP Driving Control Auto X AGP Driving Value DA AGP Fast Write Disabled AGP Master 1WS Write Disabled AGP Master 1WS Read Disabled AGP 3. 0 Calibration cycle Disabled :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults AGP Aperture Size: This option specifies the amount of system memory that can be used by the AGP device. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. AGP 2. 0 Mode: This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to your system. Make sure your graphics card supports the mode you select. AGP Driving Control: Leave this item to its default setting. AGP Driving Value: 3-9 Leave this item to its default setting. AGP Fast Write: Two options are available: Disabled $ Enabled. If your AGP adapter can support this function, then you can choose Enabled. [. . . ] They will be more familiar with local conditions and will have better insight as to which resellers offer what products and services. Due to the huge number of emails coming in every day and other reasons, such as the time required for problem reproduction, we will not be able to reply to every email. Please understand that we are selling through distribution channels and while we don't have the resources to serve every end-user, we will do our best to help every customer. Please also remember that for many of our technical support team English is a second language. [. . . ]