User manual ABIT LX6E

[. . . ] Pentium II Mainboard USER' MANUAL S Table of Contents Chapter 1 Introduction of LX6 Features ¬ Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 - Layout diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 ® The system block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Chapter 2 Installing the Mainboard ¬ Installing the Mainboard to the Casing . . . . . . . . . . . . . . . . . . . . 2-3 - Standard External Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 ® Jumper and Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 ¯ Installation of the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 ° Installing System Memory ¡i DRAM Memory ¡j2-11 Chapter 3 Introduction of BIOS ¬ CPU Setup ¡i CPU SOFT MENUTM¡j. . . . . . . . . . . . 3-3 ® ¯ ° ± ² ³ ´ µ Standard CMOS Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 BIOS Features Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Chipset Features Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Power Management Setup Menu . . . . . . . . . . . . . . . . . . . . . . . 3-17 PCI & Onboard I/O Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Min Saving When the three saving modes are enabled, the system is set up for minimum power savings. Doze = 1 hour Standby = 1 hour Suspend = 1 hour Max Saving When the three saving modes are enabled, the system is set up for maximum power savings. Doze = 1 minute Standby = 1 minute Suspend = 1 minute ä PM Control by APM: Power Management is completely controlled by the APM. APM stands for Advanced Power Mangement, it is a power management standard set by Microsoft, Intel and other major manufacturers. Video Off Method: Three video off methods are available: "Blank", "V/H SYNC+Blank" and "DPMS". The default is "V/H SYNC+Blank". If this setting does not shut off the screen, select "Blank". If your monitor and video card support DMPS standard, select "DPMS". Introduction of BIOS 3-19 Video Off After: Select the saving mode in which the video is switched off. ä ä ä ä NA The video will never be switched off in no saving mode. Doze The video will be switched off in all saving modes. Standby The video will only be switched off in Standby or Suspend mode. Suspend The video will only be switched off in Suspend mode. IDE HDD Power Down: If the system has not accessed data on the hard disk drive during the specified time period, the engine of the HDD will stop in order to save electricity. You can set 1 to 15 minutes or select Disable according to your use of the HDD. Doze Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning that computer is inactive during this period, the system will enter the Doze power saving mode. If this mode is disabled, the system will enter the next mode in the sequence (Standby or Suspend mode). Standby Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning the computer is inactive during this period, the system will enter the Standby power saving mode. If this mode is disabled, the system will enter the next mode in the sequence (Suspend mode). 3-20 Chapter 3 Suspend Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning the computer is inactive during this period, the system will enter the Suspend power saving mode. If this mode is disabled, the system will not enter the Suspend mode. Throttle Duty Cycle: This is used to specify the CPU speed in saving mode. Seven options are available: 12. 5%, 25. 0%, 37. 5%, 50. 0%, 62. 5% or 75. 0% . CPU Fan Off In Option: CPU fan can be turn off in suspend mode. Power Button Override: Support ACPI Power Button Over-ride. The user presses the power button for more then four seconds while the system is in the working state, then the system will transition to the soft-off(Power off by software). This is called the power button over-ride. IRQ8 Break Suspend : Support RTC alarm wake up from suspend function (via IRQ8). Reload Global Timer Events When one of the speficied occurs, the count down made for entry in power saving mode goes back to zero. Since the computer will enter a power saving mode only after an inactivity delay specified (time speficied for Doze, Standby and Suspend modes) and after it has no activity, during this time period, any event will cause the computer to re-count the time elapsed. [. . . ] If the above mentioned problem occurs during BIOS update you will be able to use this disk to automatically execute a BIOS update. The content of the disk should be the following: a. Startup system files (COMMAND. COM, MSDOS. SYS, IO. SYS. . . ) b. The NEWBIOS file which can be downloaded from ABIT's website. [. . . ]