User manual ABIT NF-M2S

[. . . ] NF-M2P NF-M2S NF-M2SV Motherboard AMD Socket AM2 Installation Guide Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. 12 NF-M2P/NF-M2S/NF-M2SV 1. 8. 2 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by SATA cable. Attach either end of the signal cable to the SATA connector on motherboard. Attach the other end to the SATA device. Attach the SATA power cable to the SATA device and connect the other end from the power supply. The motherboard in this photo is served for DEMO only, and may not be the same type or model as the one described in this manual. 1. 8. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. NF-M2P: NF-M2S/NF-M2SV: NF-M2P/NF-M2S/NF-M2SV 13 NF-M2S/NF-M2SV: 1. 8. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 14 NF-M2P/NF-M2S/NF-M2SV 1. 8. 5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. 1. 8. 6 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEX16". Install PCI Express X1 card into slot "PCIEX1". Install PCI cards into slots "PCI1" and/or "PCI2". Pin 1 2 3 4 5 6 7 8 9 10 Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel NF-M2P/NF-M2S/NF-M2SV 15 1. 9 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: NF-M2P/NF-M2S: · · LAN1: Connects to Local Area Network. AUDIO1: (For model NF-M2P/NF-M2S) Cen. /Sub. (Center / Subwoofer): Connects to the center and subwoofer channel. (Rear Left / Rear Right): Connects to the rear left and rear right channel. (Surround Left / Surround Right): Connects to the surround left and surround right channel. Line-In: Connects to the line out from external audio sources. Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. AUDIO1: (For model NF-M2SV) Line-In: Connects to the line out from external audio sources. Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. · NF-M2SV: · · · · · · Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. BIOS Setup This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. [. . . ] Power supply wattage: Type in the power wattage of your power supply unit. Storage devices: Type in the brand and specifications of your HDD drive and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports, including the RAID allocation status. Example 1: WD Caviar WD600 60GB (on IDE2 master), Maxtor DiamondMax 10 SATA 300GB (on SATA 3) Example 2: Maxtor DiamondMax 10 SATA 300GB *2 (on SATA 3, SATA 4 RAID 1) Optical devices: Type in the brand and specifications of your optical drives and quantity. [. . . ]