User manual ABIT SD7-533

[. . . ] Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] The enabled items will apear white in color and disabled items will show in a blue green color. " IDE Burst Mode: Two options are available: Disabled or Enabled. Selecting Enabled reduces latency between each drive read/write cycle, but may cause instability in IDE subsystems that cannot support such fast performance. If you are getting disk drive errors, try setting this value to Disabled. This field is not available to enter when the "Internal PCI/IDE" field is Disabled. " IDE Primary Master PIO: Six options are available: Auto ) Mode 0 ) Mode 1 ) Mode 2 )Mode 3 ) Mode 4. The BIOS can auto-detect the transfer mode of the IDE devices in order to set its data transfer rate (Default). You can select the PIO mode from Mode 0 to Mode 4 of the IDE devices in order to set its data transfer rate. This field is not available to enter when the "Internal PCI/IDE" field is Disabled or Secondary. " IDE Primary Slave PIO: Six options are available: Auto ) Mode 0 ) Mode 1 ) Mode 2 )Mode 3 ) Mode 4. The BIOS can auto-detect the transfer mode of the IDE devices in order to set its data transfer rate (Default). You can select the PIO mode from Mode 0 to Mode 4 of the IDE devices in order to set its data transfer rate. This field is not available to enter when the "Internal PCI/IDE" field is Disabled or Secondary. SD7-533 Motherboard Introducing the BIOS 3-19 " IDE Secondary Master PIO: Six options are available: Auto ) Mode 0 ) Mode 1 ) Mode 2 )Mode 3 ) Mode 4. The BIOS can auto-detect the transfer mode of the IDE devices in order to set its data transfer rate (Default). You can select the PIO mode from Mode 0 to Mode 4 of the IDE devices in order to set its data transfer rate. This field is not available to enter when the "Internal PCI/IDE" field is Disabled or Primary. " IDE Secondary Slave PIO: Six options are available: Auto ) Mode 0 ) Mode 1 ) Mode 2 )Mode 3 ) Mode 4. The BIOS can auto-detect the transfer mode of the IDE devices in order to set its data transfer rate (Default). You can select the PIO mode from Mode 0 to Mode 4 of the IDE devices in order to set its data transfer rate. This field does not appear when the "Internal PCI/IDE" field is Disabled or Primary. " Primary Master Ultra DMA: Two options are available: Disabled or Auto. Ultra DMA is a DMA data transfer protocol that utilizes ATA commands and the ATA bus to allow DMA commands to transfer data at a maximum burst rate of 100 MB/sec. If you encounter the problem of using Ultra DMA devices, you can try to set this item to Disabled. When you select Auto, the system automatically determines the optimal data transfer rate for each IDE device. This field is not available to enter when the "Internal PCI/IDE" field is Disabled or Secondary. " Primary Slave Ultra DMA: Two options are available: Disabled or Auto. Ultra DMA is a DMA data transfer protocol that utilizes ATA commands and the ATA bus to allow DMA commands to transfer data at a maximum burst rate of 100 MB/sec. [. . . ] If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. They will be more familiar with local conditions and problems and will have better insight as to which resellers offer what products and services. Due to the huge number of emails coming in every day and other reasons, such as the time required for problem reproduction, we will not be able to reply to every email. [. . . ]