User manual ABIT SG-80DC

[. . . ] Introduction Hardware Setup BIOS Setup Driver & Utility SG-80DC Motherboard Intel Pentium 4 Socket 775 Appendix Installation Instruction Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Use your right thumb and forefinger to grasp the CPU package. Align the notch key on the module with the rib on the slot. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snaps into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fit in one direction. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly. 2-10 SG-80DC 2. 5. 3 Floppy and IDE Disk Drive Connectors Hardware Setup The FDD connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDD on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both the FDD port and the floppy connector. Each of the IDE port connects up to two IDE drives at Ultra ATA/100 mode by one 40-pin, 80-conductor, and 3-connector Ultra ATA/66 ribbon cables. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. SG-80DC 2-11 2. 5. 4 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by a thin SATA cable. The disk array for RAID 0 or RAID 1 configuration is also provided through these SATA connectors. To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the SATA power cable to the SATA device and connect the other end from the power supply. 2-12 SG-80DC 2. 5. 5 Accelerated Graphics Port Slot This slot supports an optional AGP graphics card up to AGP 8X/4X mode. This motherboard does not support 3. 3V AGP cards. Use only 1. 5V or 0. 8V AGP cards. Hardware Setup 2. 5. 6 PCI Add-on Slots These slots provide the connection of add-on cards that comply with PCI specifications. SG-80DC 2-13 2. 6 Connecting Optional Devices 2. 6. 1 Additional USB 2. 0 Port Headers Besides the 4x USB 2. 0 ports located at rear I/O part, this motherboard also features 2x more USB 2. 0 headers onboard. Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 2. 6. 2 Internal Audio Source Connector This connector connects to the audio output of internal CD-ROM drive or add-on card. 2-14 SG-80DC 2. 6. 3 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. · · To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis. To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at pin 5-6, and pin 9-10 (default setting). Hardware Setup Pin 1 2 3 4 5 6 7 8 9 10 Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel SG-80DC 2-15 2. 7 Connecting I/O Devices The rear I/O part of this motherboard provides the following I/O ports: · · · · · · · · Mouse: PS/2 mouse connector. AUDIO: Line In: Connects to the line out from external audio sources. [. . . ] · Last name: Type in your last name. · Subject: Type in the model name and the problem of your motherboard. Example 1: AA8XE and SCSI 29160 malfunction Example 2: AA8XE boot fails, POST code AF Example 3: AA8XE (system hang when S3 resume) · Motherboard: Type in the model name and revision number of your motherboard. Example: AA8XE REV: 1. 00 · BIOS Version: Type in the BIOS version of your motherboard. [. . . ]