User manual ACER AL1511

[. . . ] . TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITOR --------------------FEATURES -------------------------------------------------------PACKING LIST --------------------------------------------------INSTALLATION INSTRUCTIONS --------------------------CONTROLS AND CONNECTORS -------------------------ADJUSTING THE VIEWING ANGLE ----------------------3 3 3 4 5 6 OPERATING INSTRUCTIONS ------------------------------------- 7 GENERAL INSTRUCTIONS ---------------------------------- 7 HOW TO ADJUST A SETTING ------------------------------ 9 ADJUSTING THE PICTURE ------------------------------ 9-10 PLUG AND PLAY ----------------------------------------------- 11 TECHNICAL SUPPORT(FAQ) ---------------------------------12-13 ERROR MESSAGE & POSSIBLE SOLUTION ------- 14 APPENDIX ------------------------------------------------------------- 15 SPECIFICATIONS ------------------------------------------ 15-16 FACTORY PRESET TIMING TABLE --------------------- 17 CONNECTOR PIN ASSIGNMENT ------------------------ 17 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. BEFORE YOU OPERATE THE MONITOR FEATURES · · · · · · 38. 1cm(15") TFT Color LCD Monitor Crisp, Clear Display for Windows Recommened Resolutions: 1024 X 768 @60Hz EPA ENERGY STAR® Ergonomic Design (TCO'99 Approved) Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: 1. LCD Monitor Owner's Manual Power Cord 15-pin D-Sub Cable Audio Cable(Option-only for Audio model) 3 INSTALLATION INSTRUCTIONS SWIVEL BASE IVEL BASE Install Remove POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 4 CONTROLS AND CONNECTORS CABLE CONNECTIONS Connect one end of the 15-pin VGA cable to the back of the monitor and connect the other end to the computer's D-Sub port. Connect the audio cable: (Option-only for Audio model)Connect the audio cable between the monitor's audio input and the PC's audio output (green port). Connect the audio cable: Plug the power cable of your monitor into a nearby outlet. Plug the other end of the power cord into the PC port. ATTENTION: If the AC outlet is not grounded, install the proper grounding adapter (not supplied). Connect the signal cable: 3 Figure 1 1. Signal Cable Power Cable Audio cable (Option-only for Audio model) 5 ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from -5° to 20°. Figure 2 NOTES · Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. · Careful attention is required not to catch your fingers or hands when you change the angle. 6 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. · The power cord should be connected. · Connect the video cable from the monitor to the video card. · Press the power button to turn on the monitor position. The power indicator will light up. Figure 3 EXTERNAL CONTROLS 1. [. . . ] 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. 11 TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Possible Solution *Check if the Power Switch is in the ON position *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Adjust the Contrast and Brightness Controls. [. . . ]