User manual ACER AL2616WD

[. . . ] . TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS --------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS -------------------- 3 BEFORE YOU OPERATE THE MONITOR ---------------------FEATURES -------------------------------------------------------PACKING LIST --------------------------------------------------CONTROLS AND CONNECTORS --------------------------ADJUSTING THE VIEWING ANGLE -----------------------3 3 3 5 6 OPERATING INSTRUCTIONS -------------------------------------- 7 GENERAL INSTRUCTIONS ----------------------------------- 7 HOW TO ADJUST A SETTING ------------------------------- 9 ADJUSTING THE PICTURE ------------------------------ 10-11 PLUG AND PLAY ----------------------------------------------- 12 TECHNICAL SUPPORT(FAQ) --------------------------------- 13-14 ERROR MESSAGE & POSSIBLE SOLUTION --------15 APPENDIX ------------------------------------------------------------- 16 SPECIFICATIONS ------------------------------------------ 16-17 FACTORY PRESET TIMING TABLE --------------------18 CONNECTOR PIN ASSIGNMENT ------------------------ 19 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 4 CONTROLS AND CONNECTORS CABLE CONNECTIONS Turn off your computer before performing the procedure below. 1 Plug the power cable of your monitor into a nearby outlet. Plug the other end of the power cord into the PC port. Connect one end of the 15-pin VGA cable to the back of the monitor and connect the other end to the computer's D-Sub port. (Only dual-input model)Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. Turn on your monitor and computer. Figure 2 1. Power Cable Signal Cable Connecting Cables DVI Cable(Only dual-input model) 5 ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the · Hold the stand so you do not topple the monitor when you change the · You are able to adjust the monitor's angle from -5° to 15°. monitor's angle. monitor, then adjust the monitor's angle to your own preference. Figure 3 NOTES · Do not touch the LCD screen when you change the angle. It may cause · Careful attention is required not to catch your fingers or hands when you change the angle. damage or break the LCD screen. 6 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. · The power cord should be connected. · Connect the video cable from the monitor to the video card. · Press the power button to turn on the monitor position. The power indicator will light up. Figure 4 EXTERNAL CONTROLS 1. [. . . ] Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. 12 TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Possible Solution *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Adjust the Contrast and Brightness Controls. *Check if the Power Switch is in the ON position Picture is fuzzy Picture bounces or a wave *Move electrical devices that may cause pattern is present in the picture electrical interference. The power LED is ON (orange) *Computer Power Switch should be in but there's no video or no the ON position. *Computer Video Card should be snugly picture. [. . . ]