User manual ACER AL711

[. . . ] This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. [. . . ] Attempting this will result in damaging the Monitor and Monitor stand. Detaching LCD Monitor from Its Stand Unscrew screws OE the swivel base support column and pull down· the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, Connecting the Display Figure 1-4 1. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port . (For AL712/AL713)(See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. Attention: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. 4 Connecting the AC Power 1. Connect the power cord to the LCD Monitor. (See Fig. Connect the power cord to an AC power source. Figure 1-6 Connecting the Audio Cable (For AL712/AL716) 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. Connect the other end of the audio cable to the LCD Monitor's " LINE IN " jack. Figure 1-7 Setting Up the LCD Monitor 1. Turn on the LCD monitor's hard power switch, located on the back of the monitor 2. Turn on the LCD Monitor's soft power switch, located on the bezel of the monitor. Figure 1-8 Power Management System This LCD Monitor complies with the VESA DPMS (version 1. 0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1 2 3 4 Stereo Speakers (AL712/AL716) Speaker Volume Control (AL712/AL716) Soft Power Switch DC Power-On Indicator PC Audio Stereo output. Decrease Volume - Turn knob counter clockwise Press the soft power switch to switch the monitor ON/OFF. LED lights Yellow --- Monitor is in "Power Saving Mode". LED is off --- Power is OFF. 5 5 6 7 Function Select Buttons Adjustment Control Buttons External Headphone Jack (AL712/AL716) Press either left or right control button for OSD (On Screen Display) menu selection. Press the left button to decrease the OSD setting and press the right button to increase the OSD setting. The monitor speakers will be disabled when using an external headphone or external speakers. Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. OSD Function Menu To access OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. [. . . ] Click " No" on " Shut Down Windows" and back to the normal PC operating environment. PROBLEM There is no picture on LCD Monitor If there's no picture on the LCD Monitor, please perform the following steps: 1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. Refer to Chapter 3 for information on timing. Turn off the LCD Monitor and then turn it back on again. [. . . ]