User manual ACER ALTOS G300

[. . . ] Acer Altos G300 User's guide Copyright © 2002 Acer Incorporated All Rights Reserved. Acer Altos G300 User's guide Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose. [. . . ] The event log data is only available if `valid'. Enabled Disabled Allow/Not allow logging of ECC events. Allow/Not allow logging of chassis intrusion events. Enabled Disabled Enabled Disabled Options Event Log Data Event Logging ECC Event Logging Intrusion Event logging 64 4 Setup utility Parameter Clear Intrusion Status Clear All Event Logs Description Clear chassis intrusion status and set this value as `disabled' at next time system boot if this item is enabled. Clear event log area and set this value as `disabled' at next time system boot if this item is enabled. This allows user to see the detail BIOS and IPMI event. Mark all events in the event log area as read. Options Yes No Yes No View Event Log Mark All Events As Read N/A N/A View Event Log This allows user to see the detail BIOS and IPMI event. 00/00/00 00/00/00 90/03/01 90/03/02 90/03/10 90/03/12 00:00:33 00:02:15 00:13:04 00:07:50 00:55:37 00:58:37 View Event Log CMOS Battery Failure CMOS System Options Not Set CMOS System Options Not Set CMOS System Options Not Set CMOS System Options Not Set CMOS System Options Not Set Mark All Events As Read Mark All Event Log Records As Read [OK] [Cancel] 65 OnBoard Devices Configuration BIOS SETUP UTILITY Advanced OnBoard Devices Configuration ____________________________________________________ OnBoard LAN [Enabled] OnBoard PCI VGA [Enabled] Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter OnBoard LAN Description Enable or disable onboard LAN. Options Enabled Disabled OnBoard PCI VGA Enable or disable onboard VGA. Enabled Disabled System Health Monitoring Hardware Hardware Monitor Setup Page This page lets you install hardware monitoring parameters so that the system can warn you when critical parameters are exceeded. 66 4 Setup utility System Hardware Monitor If your mainboard supports hardware monitoring, these items are auto-detected and the results are reported. You cannot make changes to these items. BIOS SETUP UTILITY Advanced System Health Monitoring Hardware Configure System ____________________________________________________ Health Monitoring Case Status Closed Hardware parameters. 260C/780F Current CPU Fan Speed [4200RPM] Current System Fan 1 Speed [0RPM] Current System Fan 2 Speed [0RPM] Voltage monitoring Select Screen Select Item Change Option General Help Save and Exit Exit + - F1 F10 ESC V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter Case Status Description The current status detected by chassis intrusion switch. Current CPU temperature detected by the sensor on the board. Current board temperature detected by the sensor on the board. Current CPU Fan speed detected. Current CPU1 Temp Current System Temp Current CPU Fan Speed Current System Fan 1 Speed Current System Fan 2 Speed Current System Fan 1 speed detected. Current System Fan 2 speed detected. 67 Parameter Voltage monitoring Description Press `Enter' to view the voltage monitored. Voltage monitoring BIOS SETUP UTILITY Advanced System Health Monitoring Hardware ____________________________________________________ VTT 1. 2408 V Vcc 12V 11. 9375 V Vcc 5V 4. 9660 V Vcc 3. 3V 3. 3024 V Vcc 2. 5V 2. 4960 V CPU Vcore 1. 4554 V LAN 1. 5V 1. 5087 V Vcc 5V Standby 5. 0700 V Vcc 3. 3V Standby 3. 3368 V VGA 2. 5V 2. 4960 V Vdd_IMB 1. 5V 1. 4946 V Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. 68 4 Setup utility Remote Access Configuration BIOS SETUP UTILITY Advanced Configure Remote Access type and parameters Select remote ____________________________________________________ access type Remote Access [Serial (ANSI)] Serial Port Mode [115200 8, n, 1] Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter Remote Access Description Select remote access type. Options Disabled Serial (ANSI) Serial Port Mode Select Serial Port setting. 115200 8, n, 1 57600 8, n, 1 19200 8, n, 1 9600 8, n, 1 69 Setup submenu: Power BIOS SETUP UTILITY Main Advanced Power Boot Security Exit AC Power Failure Power Button Mode Enable RTC Resuming From S4 [Last State] [On/Off] [Enabled] Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter AC Power Failure Description This sets the power state after a shutdown due to an unexpected interrupt of AC power. If the value is set to "Stay OFF, " the system remains turned off. If the value is set to "Last State, " the system returns to the last power state. If this item is set to "On/Off, " the power button acts as a standard on/ off switch. If you set this item to "Suspend, " pressing the power button enters the system into a power-saving suspend mode. Enable or Disable RTC (Real Time Clock) resume from ACPI S4. [. . . ] Passing control to INT 19h boot loader next. A9h Aah Abh B0h B1h 00h Bus Checkpoint Codes The system BIOS passes control to different buses at the following checkpoints: Checkpoint Code 2Ah Description Initializing the different bus system, static, and output devices, if present. Initialized bus input, IPL, and general devices, if present. Displaying bus initialization error messages, if any. Initializing bus adaptor ROMs from C8000h through D8000h. 38h 39h 95h 92 Appendix A: AMIBIOS POST Checkpoint Codes Additional Bus Checkpoints While control is inside the different bus routines, additional checkpoints are output to I/O port address 0080h as word to identify the routines being executed. [. . . ]