User manual ACER AR585 F1 QUICK START GUIDE

[. . . ] 6 SCREEN POSITION ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 WALL MOUNTING (OPTIONAL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CONNECTING THE POWER CORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SAFETY PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Blink frequently to keep your eyes from drying out. Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity. Eliminate glare and reflections by: placing your display in such a way that the side faces the window or any light source minimizing room light by using drapes, shades or blinds using a task light changing the display's viewing angle using a glare-reduction filter using a display visor, such as a piece of cardboard extended from the display's top front edge Avoid adjusting your display to an awkward viewing angle. Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: Take short breaks regularly and often. Exercise regularly and maintain a healthy body. We do not recommend using the product on a couch or bed. If this is unavoidable, work for only short periods, take breaks regularly, and do some stretching exercises. For more information and help in recycling, please visit the following websites: Worldwide: http://global. acer. com/about/sustainability. htm EN- 4 AR585 F1W UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. LCD Monitor 15-pin D-Sub Cable DVI Cable (Only Dual-Input Model) AC Power Cord User Manual Quick Start Guide EN- 5 AR585 F1W ATTACHING / REMOVING THE BASE Install: Align the release button on the bottom of the monitor with the corresponding slots on the bottom of the base. SCREEN POSITION ADJUSTMENT In order to optimize the best viewing position, you can adjust the tilt of the monitor by using both of your hands to hold the edges of the monitor as shown in the figure below. The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated by arrow below. EN- 6 AR585 F1W WALL MOUNTING (OPTIONAL) To obtain a wall-mounting kit, contact your local dealer, Refer to the instructions that come with the base mounting kit. Screw holes (100 mm X 100 mm) * For use only with UL Listed Wall Mount Bracket EN- 7 AR585 F1W CONNECTING THE POWER CORD Check first to make sure that the power cord you use is the correct type required for your area. 11 12 13 14 15 16 17 18 19 Pin Function T. M. D. S Clock Ground T. M. D. S ClockNC NC Clock line (SCL) Data line (SDA) Ground +5V Hot Plug Detect EN- 12 AR585 F1W STANDARD TIMING TABLE To reduce the need for adjustment for different modes, the monitor has default setting modes that are most commonly used as given in the table below. For optimum adjustment, the user is suggested to perform the Auto Setup under Windows "Full Screen" pattern or using the pattern in the floppy disk provided. 3. Empowering / Exit: 1) When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2) When OSD menu is in off status, press this button to select scenario mode. 4. Auto Adjust button / Exit: 1)When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2)When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. < / > Press < or > to select the desired function. Press < or > to change the settings of the current function. 6. MENU / ENTER: Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON. EN- 15 AR585 F1W HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window. [. . . ] Check if video signal cable is properly connected at the back of monitor. Check if the power of computer system is ON. Check if the specification of graphics adapter and monitor is in compliance which may be causing the input signal frequency mismatch. Using OSD, adjust RESOLUTION, CLOCK, CLOCK-PHASE, H-POSITION and VPOSITION with non-standard signals. [. . . ]