User manual ACER ASPIRE S7-391

[. . . ] Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondense concerning your unit should include the serial number, model number, and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated. Model Number : _________________________________ Serial Number: ___________________________________ Purchase Date: ___________________________________ Place of Purchase: ________________________________ Acer and the Acer Logo are registered trademarks of Acer Inc. [. . . ] Subsequent message boxes ask for confirmation; respond appropriately. Note that when a new array is configured, its partition record is invalidated. 89 Installing Windows NT 4. 0 and Windows 2000 Drivers Use the following procedure to install the IDE Software RAID Windows NT 4. 0 or IDE Software RAID Windows 2000 driver on to the RAIDconfigured drives connected to the primary or secondary IDE channel. Step 1 Description Boot the system with the Windows NT or Windows 2000 Boot Installation CD or diskette. Press <F6> when the following message is displayed: 2 "Setup is inspecting your computer hardware configuration. " 3 When installation prompts for a key after copying some files, press <S> to add a SCSI adaptor. Select Other from the list displayed on-screen. Insert the IDE Software RAID driver floppy diskette and press <ENTER>. Select LSI Logic IDE Software RAID driver from the list and click OK. Continue with the installation process. 4 5 6 7 Updating the Windows NT 4. 0 or Windows 2000 Driver Use the following procedure to update the IDE Software RAID Windows NT 4. 0 or IDE Software RAID Windows 2000 driver or install the IDE Software into an existing system booted from a standard IDE or SCSI drive controller. Step 1 2 3 Description Click on the Windows Start button. Click on Control Panel. 90 5 Configuring IDE Software RAID 4 5 6 Select SCSI Adapters. If the IDE Software RAID is already enabled, it will appear in the list as "LSI CSB6 Controller. " Select and remove it by clicking the Remove button. Insert the floppy diskette into the floppy drive. Select LSI CSB6 Controller and click OK. This frame displays the type of actions you can perform. It also displays extended options and links when certain links are selected. Left Middle Upper Middle Lower Right This table lists the options in the left frame. You can click the options to perform actions or display the related screens. 99 Name Scan Devices Description Re scans the system for new hard drives. After you click this button, the driver re scans all PCI devices. You will notice a significant decrease in system performance for a few seconds. Displays the RAID configuration, media errors, and status of the drives and arrays. It also allows you to start activity on a particular array. Logical View - displays information about the arrays. Physical View - displays all hard drives attached to the IDE Software RAID controller. Displays the progress bar for the current activity on the IDE Software RAID controller. The progress bar displays the time left and percentage complete. [. . . ] For more information, refer to the documentation that came with your system rack. The distance from the center of two holes with closer spacing to the center of the next pair is equivalent to 1U. When installing components, you must start your measurement from the center of the two holes with closer spacing. Otherwise, the screw holes on the component may not match those on the rack. 139 Screw types for rack installation The following screws are used in the assembly of the Acer Altos G301 and other rack-mountable components. Screw type 1 #8-32 x 0. 25 inch Figure Usage Securing the inner mounting rails to the server tray Attaching the side handles to the server 2 Hex head #6-32 0. 25 inch 3 M4 x L8 M4 nut Securing the mounting brackets to the inner sliding piece 4 M6 x L10 Securing the cable carrier and the mounting rails to the rack Cage nut Supports the M6 metal screws for securing server components to the rack Installing cage nuts Cage nuts are use to secure systems and other components to the vertical rails in the rack. To install cage nuts: 1 Insert the lower lip of the cage nut over the bottom of the opening at the back of a rail. 140 2 Appendix C: Rack installation guide Pinch the cage nut lips with your fingers and press until it locks into place. 3 Repeat this process to install the other cage nuts in their appropriate locations. 141 Installing the system into the rack To install the system into the rack: 1 2 Remove the front panel from the server. [. . . ]