User manual ACER ASPIRE T3-600

[. . . ] Reading: 800 KB/S Windows98/Me/2000/XP, MAC OS 9. x, Linux2. 4 Core 16 ohm earphone10mW10mW output Max 17 hours, 128M MPEG1 Layer1:32K-448K bps; MPEG1 Layer2: 32K-384K bps; MPEG1 Layer3:32K-320K bps; MPEG2/2. 5 Layer1: 32K-256K bps; MPEG2/2. 5 Layer2: 8K-160K bps; MPEG2/2. 5 Layer3: 8K-160K bps; 64MB/128MB/256MB 96×26 dots -20ºC~ +40ºC -40ºC ~ +60ºC 96. 5mmx30mmx21mm Writing over one million times, reading doesn't influence the life; data can be stored over ten years Installation only be needed under Windows98, other operation systems don't need to install, such as Windows Me, Windows 2000 and above Capacity LCD Display Operating Conditions Common Conditions Size Life-span Driver 1. 5 The system requirement of Acer Advanced MP3 Player 1) PC Hard disk Requirements: IBM PC, compatible PC, notebook with USB interface 2) Operator System Requirements Microsoft Windows XP/2000/ME/98 or Mac OS 9. X, Linux 2. 4 Core above or other operator systems which support the protocol of USB Mass Storage Installation Guide of Acer Advanced MP3 Player 2. 1 Windows98 Operation System Under win98, this installation will install the driver & Tool for the player. 1) Put the driver CD into CD-ROM. 3 2) . An Autorun interface will appear, click the Installation ICON and the follow window will appear: 3) Click the Next button and follow the install wizard steps, the following window will appear: 4) Click the Finish button; it will pop up a window as the follow. 4 5) Click the button Finish and the system will restart, after the system is rebooted, insert the player into the USB port and a "Removable disk" symbol will appear. That means you can use Acer Advanced MP3 Player as a hard disk. 2. 2 Windows Me/2000/XP Operation System Under win2000/XP, the installation will setup the tools only for the MP3 player. 2 An autorun interface will appear, click the Installation ICON and the follow window will appear: 5 3 Click the Next button and follow the install wizard steps, the follow window will appear: 4 Click the Finish button; it will install the tools completely. [. . . ] can change the EQ mode by using the " 4. . 5 4 5 A--B Repllay A B Rep ay In play mode, press the mode key to enter the play menu, select A-B replay and you can replay the song or paragraph you select, see the following picture: As you enter the A-B replay mode, when the letter A is blinking, press Next key to set the start point; when the letter B is blinking, press Next key to set the end point. The player will replay the song snippet you select. 10 To cancel the A-B replay mode, Please press the mode key. 4. . 6 4 6 Vollume Conttroll Vo ume Con ro When MP3 is on standby or playing, press "VOL+" or "VOL -" button to control the volume and the LCD will show the following graphics: 4. . 7 4 7 HOLD Functtiion HOLD Func on Using the HOLD function can prevent a malfunction of the player by accidentally pressing a wrong button. Move the HOLD switch on the side of the player to HOLD. A lock icon on the LCD panel is displayed for the setting. Move the switch to HOLD OFF and a lock icon on the display disappears, like this: 4. . 8 Maiin Menu 48 Ma n Menu In Standby mode, press the mode key and enter the main menu. Press " "or " "to select the menu item, see illustration: Enter the music directory to play MP3/WMA files, . Select this item to enter record mode. Select this item to enter the voice directory where you can play voice recording files. Select this item to enter the system setting menu. 11 Exit the main menu. 4. . 9 Systtem settttiing menu 49 Sys em se ng menu When you select the "sys function" item in the main menu, you will enter the system setting menu: "or " "to There are 12 submenus in the system setting menu. You may use " select the menu item and then press the mode key to confirm your selection. See the following illustration: Select the directory. As you select music Dir, the Player will play the music files; and if you select record Dir the device will play the voice files. 4. 13. 2 Use the sound converter tool: This tool is used for converting rcd/rec/act file recorded by an MP3 player to WAV file. It will appear as follows: [Open]: Open a WAV, MP3 or rcd/rec/act file. If it is a WAV or MP3 file you can play it back directly. If it is an rcd/rec/act file you should convert it to a WAV file before playing it back. Only enable when selecting an rcd/rec/act file. Press the Open button and an explorer windows will appear. If the file you opened is an MP3 or Wav file, you can use this tool to play it. If the file you opened is a REC/RED/ACT file, you can use this tool to transform it to a wav file. Manage your MP3 Pllayer Manage your MP3 P ayer 16 Follow the instructions below to Firmware upgrade. The firmware has two files: $norfla$. ugr and $nanfla$. ugr, but the two files are not necessary for firmware update every time, when the two files are exist, you must upgrade the two files at this time. 1) Be sure to backup your important files in your unit before Firmware Downloading. 2) Connect the unit into the USB port 3) Firstly copy the file $norfla$. ugr to the MP3 root directory. [. . . ] If you unplug the unit when the display is blinking, data may be lost!- We strongly recommend that you back up your data for safety. 17 FAQ FAQ 7. . 1 7 1 The pllayer does nott tturn on:: The p ayer does no urn on - Check if the player has the batteries installed. - Turn on your computer, connect the player to the USB port and turn on the player. - If the above step does not resolve the problem, then do a "Firmware upgrade" and format the player, you can find and download the firmware from our website. [. . . ]