User manual ACER ASPIRE T3-605

[. . . ] € Make provision for a suitable omnipolar disconnection device, with power supply cut-off, leaving more than 3 mm between the contacts 4. 2 Tools and materials Ensure you have all the tools and materials necessary for carrying out the installation according to current safety standards. (in movement) for flashing lamp Serial communication for PC connection, use bipolar shielded cable mod. RS235 PC 40 o PC30 A B GND + E - RS232 cable Personal Computer - + E E - E + - Connection for encoder (for the connection between the automation and the electric picture to use cable screened type 2402C 22AWG) 10 11 1 2 3 3P 4 5 7 CX CY TS (1. [. . . ] > ENTER < ESC < > <LANGUAGE ENTER ENTER > PROGRAMMING FUNCTION > < LINGUA > < PROGRAMMING FUNCTIONLINGUA PROGRAMMING FUNCTION > To select the menu item, move the arrows PROGRAMMING FUNCTION until you reach < > ESC ENTER one required. The < ESC < LANGUAGE < > > ENTER PROGRAMMING FUNCTION TIMING > < > ESC ENTER < LINGUA > ESC also for the menus below, move the arrows ENTER until you reach the one required. lINGUA Then press ENTER PROGRAMMING FUNCTION < > PROGRAMMING FUNCTION < > ENTER < O p e r a t i o n T i m e> ESC ESC < > PROGRAMMING FUNCTION < < > ENTER 12 FUNCTION PROGRAMMING sec < Auto Clo. Time > < > ESC 20 sec LINGUA ENTER > Then press ENTER < ESC PROGRAMMING FUNCTION If the <> arrows are pointing on the time, Auto Clo. Time > ESC this means 20 sec LINGUA it can be changed. < > < ESC PROGRAMMING FUNCTION < < > > ENTER To increase or decrease the PROGRAMMING FUNCTION value, click on the arrows > ENTER until you reach the one required. ENTER < Tutti i dati e le informazioni quì contenute sono da ritenersi susciettibili di modifica in qualsiasi momento e a nostro giudizio The < > buttons are for: - moving from one menu to another PROGRAMMING PROGRAMMING FUNCTION or decreasing a value FUNCTION - inreasing < > ESC ENTER LINGUA > ESC < Auto Clo. Time < > 45 < ESC sec > > ENTER ENTER Then press ENTER to confirm To quit the menu, wait 30 seconds or press ESC, until the initial screen appears ESC < > N. When the menu is active, you cannot carry out any manoeuvres. : automatic closing time after an opening command. : automatic closing time after an pedestrian opening command TIMING ENTER > x3 Pedestrain ACT ENTER < 10 sec > < > Functions Automatic Closure: Enables/disables the automatic closing function FUNCTIONS ENTER > Auto Closing ENTER <ON > < > <OFF> Command 2-7: Sets the sequential- or stepper contact. iNFO ENTER > Welcome Note To see detailed description 5. 5 Run calibration From the calibrations menu, select Run calibration, then confirm PROGRAMMING by pressing ENTER FUNCTION 1 Perform a complete opening run using (< >) until reaching the maximum openingPROGRAMMING FUNCTION point < 2 3 Then confirm with ENTER. ESC < > ENTER ESC < > ENTER Perform a full closing run by using (< >), until reaching the maximum closPROGRAMMING FUNCTION ing point < 4 5 Then confirm by pressing ENTER. Move the gate in the opening direction for at least 3 s. pROGRAMMING FUNCTION 6 Do a full > LINGUA closing Run S< t e opening dir LINGUA > ENT:OK <>:move ESC < > ENTER ESC < > ENTER 7 Then confirm by pressing ENTER. PROGRAMMING FUNCTION Use the (< >) to move the gate to PROGRAMMING FUNCTION the closing position. ESC < > ENTER ESC < > ENTER ESC < > ENTER Use the (< >) move the gate to PROGRAMMING FUNCTION the opening position. If the calibration has not been performed correctly, the “reprogram” message will appear and you will return to step 1. 12 ESC < > ENTER ESC < > ENTER 13 English 5. 6 Decoding boards 17 26 To control the board by remote control or pass, you must first connect the appropriate decoding board: R700 for the passes and AF for the radio-controls. If you don’t install the appropriate decoding board, you won’t be able to add any users. [. . . ] < By selecting NO, the procedure for adding users will end while by selecting YES, the procedure goes back to step 3 ESC < > ENTER 14 Tutti i dati e le informazioni quì contenute sono da ritenersi susciettibili di modifica in qualsiasi momento e a nostro giudizio 1 2 3 4 5 6 7 8 9 10 11 12 04 05 06 07 08 CANCELLI AUTOMATICI R700 ESC < > ENTER ASPIRE T3-605 CONTROL BOARD V1 V2 V3 V4 V5 5. 8 Changing users (user functions) From the Radio/Users menu, select Changing users, confirm by pressing ENTER PROGRAMMING FUNCTION ESC ENTER 1 Select the user whose function you want to change by the arrows (< >), or by pressing the transmitter button associated to it, or by swiping the pass over the sensor, and confirming with ENTER. > ESC < > ENTER ESC < > ENTER Tutti i dati e le informazioni quì contenute sono da ritenersi susciettibili di modifica in qualsiasi momento e a nostro giudizio select the function you want to associate to the user and confirm with ENTER NB Confirming with ENTER will take you back to the “Changing users” dialog. , confirm with ENTER < ESC PROGRAMMING FUNCTION LINGUA N o t e > < Welcome < > 1 The ENTER button is used for: LINGUA > - Moving PROGRAMMING FUNCTION the cursor to the right - If pressed for more than 3 secs. [. . . ]