User manual ACER AT3228ML

[. . . ] Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are indicated on the label affixed to your device. All correspondence concerning your unit should include the serial number, model number, and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated. [. . . ] Color buttons (R/G/Y/B) Operates corresponding button on the teletext page. MPX Press to select the sound input, displayed in the top right-hand corner (mono, stereo, bilingual). *Key position depends on TV model. 3 4 5 6 23 CH/PG Page up/down. 11 4. in. 1. 05. series. 0303. indb 11 3/8/2006 2:03:42 PM English Basic connections Connecting the power cord 1 2 Connect the AC cord into the AC input on the back of the set. Connect the plug to the wall outlet as shown. Setting up the remote control 1 Open the cover on the back of the remote unit. Looking after your remote control · Handle the remote control with care. Dropping, wetting or placing the remote control in sunlight may damage it. Kid · 2 Insert two AAA batteries (supplied) to match the polarity indicated inside the battery compartment. + Aug Do not tamper with batteries. Keep them away from children. · + When you anticipate that the remote control will not be used for an extended period, remove the batteries to prevent possible damage as a result of battery leakage. · Dispose of used batteries according to local regulations. Recycle if possible. 12 4. in. 1. 05. series. 0303. indb 12 3/8/2006 2:03:43 PM Enjoying analog and digital TV Connecting an antenna/cable Connect the antenna cable to the appropriate antenna terminal on the back of the TV set as shown below. Analog Digital English Getting started watching your TV 1 MPX 2 4 TELTEXT HOLD SIZE SUBTITLE 1, 3 I O 1 Power I O a. Turn on the power switch beneath the screen. 1 b. Press the power button, number keys or channel up/down button on the remote control. Setup Wizard 2 The first time you switch on the TV, the Setup Wizard will guide you to complete the language selection and channel scanning. Press the OK key to begin the setup process. You can also adjust these settings using the front control panel. Please see "Front panel view" on page 8 for details. 13 4. in. 1. 05. series. 0303. indb 13 3/8/2006 2:03:43 PM Setup Wizard English Step 1. Select the setup language you prefer. Step 2. These are: Picture, Audio, Channel management, Options, Setting and Empowering. Use the following method to navigate these menus. U 1 M EN Press the MENU button on the remote control or the MENU button on the control panel. 2 Select your desired menu by using the up and down directional keys to switch between the six menus. 3 Use the directional keys to interact with the menu. The up/down directions will scroll through the menu options, while left/right will adjust the different settings (for example, in the Picture menu, settings such as brightness, contrast, etc. ). Press MENU to exit. 18 4. in. 1. 05. series. 0303. indb 18 3/8/2006 2:03:46 PM Adjusting the OSD settings English The OSD can be used for adjusting the settings of your LCD TV. You can use the OSD to adjust the picture quality, audio settings, channel settings, general settings and the Empowering Technology settings. For advanced settings, please refer to following page: Adjusting the picture quality 1 2 3 4 Press the MENU key to bring up the OSD. Using the directional keys, select Picture from the OSD. Then navigate to the picture element you wish to adjust. Use the left or right keys to adjust the sliding scales. The Picture menu can be used to adjust the current Scenario mode, brightness, contrast, color, sharpness and other image-related qualities. Adjusting the audio settings 1 2 3 4 Press the MENU key to bring up the OSD. Using the directional keys, select Audio from the onscreen display. [. . . ] Make sure the antenna at the rear of the TV is properly connected. Make sure the main power switch is turned on. Make sure the volume is not set to minimum or the sound is not set to mute. Make sure the headphones are not connected. [. . . ]