User manual ACER G195HQ

[. . . ] This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. [. . . ] In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. BEFORE YOU OPERATE THE MONITOR FEATURES · · · · · · · Dual Input (DVI + Analog) (Only Dual-Input Model) Ergonomic Design (TCO'03 Approved) Space Saving, Compact Case Design EPA ENERGY STAR® 55. 87cm(22") TFT Color LCD Monitor Crisp, Clear Display for Windows Recommened Resolutions: 1680 X 1050 @60Hz CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: 1. LCD Monitor Owner's Manual Power Cord External Adapter 15-pin D-Sub Cable DVI Cable (only Dual-Input Model) Audio Cable Quick Start Guide 3 POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's External Adapter input socket, and then plug the other end of External adapter to LCD monitor's DCpower-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. Installing the wall mounting bracket (not included) This monitor display can be connected to the wall mounting bracket that is sold separately. Please see the following diagram for information on how to disconnect it from the power cable and fold the monitor: Installation of the wall mounting bracket is as follows: 1. The monitor can be hung from the wall by either of the two following methods: Method a: Place the wall mounting bracket on the underside of the monitor. Attach to monitor through the holes in the bracket and on the underside of monitor; Attach (10cm X 10cm) as shown in figure a. </ Volume External Control Button 4. Power Key /Power Indicator 7 FRONT PANEL CONTROL · Power Button: Press this button to turn the monitor ON or OFF, And display the monitor's state. · Power Indicator: Blue Orange -- -- Power On mode. Power off. · MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. · </Volume: Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · >/Volume: · Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. NOTES · Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. · Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. · For maximum protection, repackage your monitor as it was originally packed at the factory. · To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. [. . . ] One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. 12 TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on Possible Solution *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave *Move electrical devices that may cause pattern is present in the picture electrical interference. [. . . ]