User manual ACER G215HL QUICK START GUIDE

[. . . ] 6 Connecting the power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cleaning your monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Power saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Give your eyes regular breaks by looking away from the monitor and focusing on a distant point. · Blink frequently to keep your eyes from drying out. Display · Keep your display clean. · Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. · Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity. · Eliminate glare and reflections by: · placing your display in such a way that the side faces the window or any light source · minimizing room light by using drapes, shades or blinds · using a task light · changing the display's viewing angle · using a glare-reduction filter · using a display visor, such as a piece of cardboard extended from the display's top front edge · Avoid adjusting your display to an awkward viewing angle. · Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: · Take short breaks regularly and often. · Perform some stretching exercises. · Breathe fresh air as often as possible. · Exercise regularly and maintain a healthy body. ----------------------------------------------------------------------------------------------------Warning!DESCRIPTION Red Green Blue Monitor Ground DDC-return R-Ground G-Ground B-Ground PIN NO. DESCRIPTION +5V Logic Ground Monitor Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock EN-9 G215HL A 24-Pin Color Display Signal Cable PIN 1. 12. Meaning TMDS Data2TMDS Data2+ TMDS Data 2/4 Shield NC NC DDC Clock DDC Data NC TMDS Data1TMDS Data1+ TMDS Data 1/3 Shield NC EN-10 PIN 13. 24. Meaning NC +5V Power GND(return for +5V hsync. vsync) Hot Plug Detect TMDS Data0TMDS Data0+ TMDS Data 0/5 Shield NC NC TMDS Clock Shield TMDS Clock+ DDC TMDS Clock- G215HL A Standard Timing Table To reduce the need for adjustment for different modes, the monitor has default setting modes that are most commonly used as given in the table below. For optimum adjustment, the user is suggested to perform the Auto Setup under Windows "Full Screen" pattern or using the pattern in the floppy disk provided. When none of the mode is matched, the user can store their preferred modes in the user modes. The monitor is capable of storing up to 9 user modes. Press the MENU-button to activate the OSD window. Press < or > to select the desired function. Press the MENU-button to select the function that you want to adjust. Press < or > to change the settings of the current function. [. . . ] Save user adjustment and OSD disappear. N/A N/A N/A N/A Reset N/A Exit EN-17 G215HL A · Acer eColor Management OSD · Operation instructions Acer eColor Management Step 1: Press " Key " to open the Acer eColor Management OSD and access the scenario modes Step 2: Press "<" or ">" to select the mode Step 3: Press " Auto Key " to confirm the mode and run Auto Adjust · Features and Benefits EN-18 G215HL A TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. (VGA Mode) Problems Current Status Remedy LED ON · Using OSD, adjust brightness and contrast to maximum or reset to their default settings. Check if AC power cord is properly connected to the monitor. Check if video signal cable is properly connected at the back of monitor. [. . . ]