User manual ACER GN245HQ

[. . . ] Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondense concerning your unit should include the serial number, model number, and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated. Model Number : _________________________________ Serial Number: ___________________________________ Purchase Date: ___________________________________ Place of Purchase: ________________________________ Acer and the Acer Logo are registered trademarks of Acer Inc. [. . . ] [Auto] 32Bit Data Transfer [Disabled] ARMD Emulation Type [Auto] Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. 60 4 Setup utility Floppy Configuration BIOS SETUP UTILITY Advanced Floppy Configuration ____________________________________________________ Floppy A [1. 44MB 31/2î] Select the Floppy drive type. Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter Floppy Drive A Description Select the floppy drive type · Floppy Drive A If you have one floppy drive installed change the item Floppy Drive A so that it describes the characteristics of the drive. 61 PCIPnP Configuration BIOS SETUP UTILITY Advanced PCIPnP Configuration Legacy USB Support PCI Slot-1 IRQ Preference PCI Slot-2 IRQ Preference PCI Slot-3 IRQ Preference PCI Slot-4 IRQ Preference PCI Slot-5 IRQ Preference [Disabled] [Auto] [Auto] [Auto] [Auto] [Auto] Enables support legacy USB. for Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter Legacy USB Support PCI Slot-1 IRQ Preference PCI Slot-2 IRQ Preference PCI Slot-3 IRQ Preference PCI Slot-4 IRQ Preference PCI Slot-5 IRQ Preference Description Enable support for legacy USB. Options Enabled Disabled Manually configure the IRQ of PCI slot-1. Auto 3 4 5 7 9 10 11 12 14 15 Manually configure the IRQ of PCI slot-2. Manually configure the IRQ of PCI slot-3. Manually configure the IRQ of PCI slot-4. Manually configure the IRQ of PCI slot-5. 62 4 Setup utility Boot Settings Configuration BIOS SETUP UTILITY Advanced Boot Settings Configuration Select Power-on state ____________________________________________________ for Numlock. Bootup Num-Lock [On] Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter Bootup NumLock Description Select Power-on state for Numlock Options On Off 63 Event Log Configuration BIOS SETUP UTILITY Advanced Event Log Configuration Enabled: Allow logging of ____________________________________________________ events. Event Log Area: Event Log Data: Event Logging ECC Event Logging Intrusion Event logging Clear Intrusion Status Clear All Event Logs View Event Log Mark All Events As Read Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit Space Available Valid [Enabled] [Disabled] [Enabled] [No] [No] V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Note: If there are any event logs recorded, "View Event Log" and "Mark All Events As Read" will appear. If no event recorded, these two options will NOT appear. If you set this item to "Suspend, " pressing the power button enters the system into a power-saving suspend mode. Enable or Disable RTC (Real Time Clock) resume from ACPI S4. If this option is set to "Enable", the system could wake up from ACPI S4 (Hibernation in Windows 2000/. NET) if O. S. configured properly. Options Last State Stay Off Power Button Mode On/Off Suspend Enable RTC Resuming From S4 Enable Disable 70 4 Setup utility Setup submenu: Boot BIOS SETUP UTILITY Main Advanced Power Boot Device Priority Hard Disk Drives Removable Devices ATAPI CDROM Drives Boot Security Exit Enter F1 F10 ESC Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter Boot Device Priority Hard Disk Drives Description Specifies the boot sequence from the available devices. Specifies the available hard disk drives boot sequence. Specifies the available removable devices boot sequence. Specifies the available CD-ROM drives boot sequence. Only first drive could boot the system. Removable Devices ATAPI CDROM Drives 71 Boot Device Priority BIOS SETUP UTILITY Boot 1 Boot Device 2nd Boot Device 3rd Boot Device st [Removable Device] [ATAPI CDROM] [Hard Drive] Specifies the boot sequence from the available devices. Select Screen Select Item + - Change Option F1 General Help F10 Save and Exit ESC Exit V02. 03 ©Copyright 1985-2000, American Megatrends Inc. Parameter 1st Boot Device Description Configure the first boot device type. Options Available boot device type. 2nd Boot Device Configure the second boot device type. [. . . ] Performing any initialization required after the E000 option ROM had control next. Initialization after E000 option ROM control has completed. Displaying the system configuration next. Uncompressing the DMI data and executing DMI POST initialization next. [. . . ]