User manual ACER H226HQL

[. . . ] Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondense concerning your unit should include the serial number, model number, and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated. Model Number : _________________________________ Serial Number: ___________________________________ Purchase Date: ___________________________________ Place of Purchase: ________________________________ Acer and the Acer logo are registered trademarks of Acer Inc. [. . . ] Shadow miscellaneous ROMs if specified by Setup and CMOS is valid and the previous boot was OK. 97h 98h 99h 9Ah 32 3 Getting Started Checkpoint Code 9Ch Beep Code Description Set up Power Management. Initiate power management state machine. Check the total number of Fast Disks (ATA and SCSI) and update the bdaFdiskCount. Verify that the system clock is interrupting. Display a message if key switch is locked. Overwrite the "Press F2 for Setup" prompt with spaces, erasing it from the screen. Scan the key buffer to see if the F2 key was struck after keyboard interrupts were enabled. If an F2 keystroke is found, set a flag. Enter SETUP If (F2 was pressed) go to SETUP Else if (errors were found) display "Press F1 or F2" prompt if (F2 is pressed) go to setup else if (F1 is pressed) boot Else boot 9Dh 9Eh 9Fh A0h A2h A4h A8h AAh ACh AEh Clear ConfigFailedBit and InPostBit in CMOS. 33 Checkpoint Code B0h Beep Code Description Check for errors If (errors were found) beep twice display "F1 or F2" message if (F2 keystroke) go to SETUP if (F1 keystroke) go to BOOT B1h B2h Inform RomPilot about the end of POST. Change status bits in CMOS and/or the BIOS data area to reflect the fact that POST is complete. Turn off <Esc> and <F2> key checking. Open the system according to the instructions on page 42. Follow the ESD precautions described in this section when handling a server component. Remove any expansion board(s) or peripheral(s) that block access to the DIMM socket or other component connector. See the following sections for specific installation instructions on the component you want to install. Warning!Failure to properly turn off the server before you start installing components may cause serious damage. Do not attempt the procedures described in the following sections unless you are a qualified service technician. Post-installation instructions Observe the following after installing a server component: 1 2 3 4 5 See to it that all components are installed according to the described step-by-step instructions. Reinstall any expansion board(s) or peripheral(s) that you have previously removed. Turn on the system. 42 4 Configuring the system Opening the server Caution!Before you proceed, make sure that you have turned off your system and all peripherals connected to it. Read the "Preinstallation instructions" on page 41. You need to open the server before you can install additional components. The top panel is removable to allow access to the system's internal components. Refer to the following sections for instructions. Before opening the server Before opening the server, observe the following precautions: 1 2 3 Turn off the system and all the peripherals connected to it. [. . . ] Use the <Tab> key to scroll to the Array Label field and enter text to identify the array. Press <Enter> to confirm the array's label. 108 7 Appendix C: SATA RAID configuration utility Scroll to Stripe Size, by using the <Tab> key, and select 16 KB, 32 KB, or 64 KB using the arrow keys. Press <Enter> to confirm the array stripe size. Using the <Tab> key, scoll to the Create RAID via field and select. [. . . ]