User manual ACER H5360

[. . . ] Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of this company to notify any person of such revision or changes. Fill this in!! For the convenience of service, record the following information in the space below. The serial number is on the back of the product. Monitor Information Product 7763P/65PE Name: Serial Number: Date of Purchase: Dealer Information Dealer: Telephone Number: Address: Caution TO PREVENT SHOCK, DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL. [. . . ] If any pieces are missing, contact your dealer. Please save the original box and packing materials in case you ever need to ship the unit. English 5 Figure 7 Accessories of 7763P/65PE English 6 Connection A Connecting the Projector to Computer/Notebook 2 Figure 8 Connection to PC Figure 9 Connection to notebook English 7 B Connecting the Projector to Macintosh/Power Book Figure 10 Connection to Macintosh Figure 11 Connection to Power Book English 8 Operation 3 Turn On/Off Procedure A Power on Press the Standby/On key to turn on the lamp. The LED will blink green during warm up and then light solid green. "INPUT SIGNAL DETECTED, ACTIVATING AUTO IMAGE" will be displayed on the screen after the projector has identified the input signal; "SEARCHING" message will be displayed on the screen if there is no signal input; "SYNC IS OUT OF RANGE" message will be displayed on the screen if the horizontal frequency of the input signal exceeds the range of the projector. B Standby Press the Standby/On key for more than one second to turn off the lamp. The LED will then blink orange and the lamp will shut down, but the fan will continue to run for about 1 minute to cool the lamp. After the fan stops, the LED will turn to a light solid orange. *Lamp Protection Procedure: If you try to turn on the lamp again while the LED is blinking, the projector will ignore the command until it has cooled down for one minutes. External Control A Control Pad Figure 12 External control pad English 9 MAIN UNIT Menu FUNCTION To call the OSD menu. To navigate through sub pages or to increase the scale bar number. To navigate through sub pages or to decrease the scale bar number. To exit from the current page or OSD menu, and save setting changes. To show lamp hour message To turn the projection lamp on and off. Functions as an indicator showing the standby status. 4 3 Exit Standby/On Standby/On indicator Lamp status Lights or blinks when the lamp does not light. indicator (LED) STMANDBY/ON Laser Source Menu Exit Freeze Blank L-Click Drag R-Click Magnify Return Volume Mute English 10 B Remote Control Figure 13 Remote control The remote control allows you to operate the function keys on the projector and to emulate mouse function when the projector is connected to a computer. "CHANGE THE LAMP, AND RESET THE LAMP TIMER" will be displayed on the screen if the lamp has been operated for 1200 hours (see figure 16). "CHANGE THE LAMP, THE POWER WILL TURN OFF AFTER 20 HOURS" will be displayed on the screen if the lamp has been operated for 1479 hours. The "20" will count down (see figure 17). · If hot, the lamp could cause burns. Wait for about 45 minutes until lamp has cooled down. · Loosen a screw and remove the cover. English 14 iii. iv. v. Loosen the screw and pull the handle to remove the lamp. · If the screw is not loosened completely, you could hurt your fingers. · Do not insert your hand into the box after the lamp has been removed. (There are optical parts inside that, if touched, could result in color unevenness, etc. ) Replace the lamp with a new one and fix it using the same screw. Loose screws could result in a poor connection, which could cause the unit to malfunction. Install the lamp cover and fix it using a screw. [. . . ] Press this button to activate release the blank function. or Drag Blank English 23 Maintenance Troubleshooting A Lamp Replacement Refer to Page 11 and 4 B Cleaning the Lens Follow these steps to clean the projection lens: 1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth (abrasive cleaners, solvents or other harsh chemicals might scratch the lens). Avoid using an excessive amount of cleaner. [. . . ]