User manual ACER H5360 BD

[. . . ] TRADEMARK ACKNOWLEDGEMENT : · PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation. · Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. · VESA and SVGA are trademarks of the Video Electronics Standard Association. · Windows is a registered trademark of Microsoft Corporation. [. . . ] The basic operations of these menus are as follows. Menu screen display : Press the MENU button. Menu selection : Choose a menu name using the button, and press the button or the ENTER button. Item selection : Choose an item using the button, and press the button or the ENTER button. Return menu to last previous screen: Press the button or the ESC button. Execution of settings and/or adjustments: Operate by using the button. (For further details, read the explanation for each separate menu. ) Initialization of settings and/or adjustments: During operation, press the RESET button. (Note that items whose functions are performed simultaneously with the operation of clock phase, language selection, automatic adjustment, etc. , cannot be initialized. ) End menu operations: Press the MENU button, or do not perform any operation for several seconds. MAIN Menu With the MAIN menu, the seven items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION BRIGHT CONTRAST ASPECT PICT. GAMMA MIRROR LANGUAGE 12 : SELECT MAIN Menu Item BRIGHT CONTRAST Adjust Brightness: Light Adjust Contrast: Strong Description Dark Weak Example : MAIN Menu (BRIGHT) ASPECT Select Aspect Ratio: At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO Input: 4:3 16:9 At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input: 4:3 16:9 SMALL · The SMALL picture may not be displayed correctly with certain input signals. Select Picture Position (for 16:9/SMALL Picture): TOP CENTER BOTTOM Select Gamma Mode: NORMAL CINEMA Select Mirror Status: NORMAL H:INVERT Select Menu Language: ENGLISH FRANÇAIS ITALIANO NORSK POTUGUÊS DYNAMIC V:INVERT H&V:INVERT PICT. POSIT. GAMMA MIRROR LANGUAGE DEUTSCH ESPAÑOL NEDERLANDS 2 PICTURE 1 Menu With the PICTURE 1 menu, the five items shown in the Table below can be performed. Select HDTV Signal Mode: 1080i 1035i · If the selected HDTV mode is incompatible with the input signal, the picture may be distorted. On/Off SYNC ON G Mode: TURN ON TURN OFF Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC on G. · In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal. AUTO VIDEO HDTV SYNC ON G 4 SCREEN Menu With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION BLANK START UP MyScreen MyScreen Size MyScreen Lock MyScreen ORIGNAL : SELECT SCREEN Menu Item Description Example : SCREEN Menu (BLANK) BLANK Selection of BLANK Screen: MyScreen ORIGINAL . . The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen has been erased (i. e. , made to vanish) by manipulating the BLANK button (please refer to the "Temporarily Blanking the Screen" section of the separate booklet, Vol. MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. Please make confirmation using the actual screen(s). [. . . ] (3) The projector returns the response code `06H' to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data (`04H'+`00H'+ type (2 bytes) +`00H'+`00H') to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+`00H'+ type (2 bytes) +`00H' + `00H') to the projector. (2) The projector decreases the setting value on the above setting code. [. . . ]